Electronic Components & Devices

Rotor/Wiper Kit builds potentiometers in any size.
Resistors

Rotor/Wiper Kit builds potentiometers in any size.

Do It Yourself potentiometer element and rotor wiper assembly kit includes element shaft, shaft insulator, rotor assembly and instructions. Kit is available in standard sizes, or can be customized with virtually any dia, resistance, linearity, thickness or electrical angle required. Resulting potentiometer provides infinite resolution precision sensor that will run continuously for 100,000,000...

Read More »
Inlet/Exhaust Trap fits vacuum systems.
Filters

Inlet/Exhaust Trap fits vacuum systems.

MV Multi-Trap Model IC has stainless steel knock-down stage (for collecting heavy solids) and water-cooled internal coils with more than 200 sq. in. of surface area to collect condensables and particulates. It can be configured with 2 banks of 10, replaceable, 4-1/2 in. filter elements or 1 bank of five, 9-1/2 in. elements. High capacity trap can be used in chemical, optoelectronic,...

Read More »
Soft Shell Connectors are available in 2 to 12 positions.
Connectors

Soft Shell Connectors are available in 2 to 12 positions.

Micro MATE-N-LOK 3mm-pitch connectors have dual-beam contacts for improved mating area, and high temperature housings for IR processing. Single row contacts on 3mm centerlines accommodate installations where thin, tight connectors capable of handling up to 5 A are required. Units can provide power and signal I/O and power interface interconnections.

Read More »
Connector System works with 230V/16A AC systems.
Contacts

Connector System works with 230V/16A AC systems.

HARAX(R) detachable insulation displacement connector system provides quick termination by removing cable insulation; inserting individual, non-stripped wires; and tightening screw cap with no special tools. Gas-tight connection qualifies for IP67 rating. HARAX series provides termination components for panel feed-throughs, M8 and M12 connectors, and passive sensor/actuator boxes.

Read More »
Signal Receivers

Receiver Core is targeted for programmable logic devices.

Digital IF Receiver is designed to accept IF data samples up to 16-bits wide that are then mixed using quadrature numerically controlled oscillator to produce In-phase and Quadrature (I and Q) baseband data streams. Complex 4th order decimating cascading integrator comb filters provide programmable sample rate reduction. Programmable coefficient finite impulse response filters, with up to 64...

Read More »
PDA reads and writes to TEDS smart transducers.
Sensors / Detectors / Transducers

PDA reads and writes to TEDS smart transducers.

Model 400A75 TEDS PDA includes Palm m105 with 8MB of RAM, communication hardware that plugs into HotSync(R) port, cable, and installed software to read and write to PCB IEEE P1451.4 compliant TEDS sensors. TEDS are self-identifying transducers with fields that fully describe type, operation, and attributes of transducer. PDA reads full content of TEDS memory and displays it on Palm's LCD display.

Read More »
Interconnects combine differential and single ended systems.
Connectors

Interconnects combine differential and single ended systems.

Q-Pair high speed interconnects in differential pair configurations allow electrical performance at up to 5GHz operating frequencies. Connectors can be partitioned to include both differential pair and single-ended signal pins, allowing board designer to optimize system for high speed where required, while minimizing impact on density.

Read More »
Low-Profile LEDs provide high flux over wide angle.
Rectifiers and Diodes

Low-Profile LEDs provide high flux over wide angle.

SuperFlux LEDs have water clear lenses and provide 7,000 mcd luminous intensity @70 mA current over 65 or 85 deg viewing angle, depending upon version. Measuring 7.62 mm sq. with 4.4 mm high body, through-hole LEDs can be mounted close together in clusters to fit wide variety of illumination applications in aviation, automotive, marine, industrial, and emergency signs. Colors include green,...

Read More »
Core Pins are offered in 500 diameters.
Pins

Core Pins are offered in 500 diameters.

M-2 high speed steel core pins are available in every decimal dia from 0.010 to 0.505 in. in 0.001 in. increments, with 0.0002 in. or 0.0003 in. dia tolerances. Double-tempered to Rc 60-63, pins are wear-resistant and permit close spacing without modification. They are available in 2, 2 1/2, 3, 4, 6 and 8 in. lengths and are suited for glass-filled applications.

Read More »
Cut and Bevel Pipe up to 63" Diameter with a Single Lightweight, Portable Machine
Sponsored

Cut and Bevel Pipe up to 63" Diameter with a Single Lightweight, Portable Machine

CS Unitec is a leader in power tools designed for industrial applications, with products that set the standard for robust performance and industry-leading reliability. Adding to our long list of innovation is a new line of pipe cutting machines. For cutting and beveling pipe up to 2" in thickness and diameters from 12" to 63", no other cutting system comes close. See our video to learn more.

Read More »

All Topics