Electronic Components & Devices

Locking Pins are used where quick release is needed.
Pins

Locking Pins are used where quick release is needed.

Kwik-Lok pins are available in five handle styles: T, L, button, recessed button and ring. When buttons are depressed, balls at end of grip shaft retract, permitting insertion or removal. Standard sizes range from 3/16 to 1 in. OD in 1/2 to 6 in. grip lengths. Metric sizes are available from 5-25mm OD in 10-100mm grip lengths. All are made of 17-4 PH stainless steel or carbon steel.

Read More »
GDC Filter has durable plastic frame.
Filters

GDC Filter has durable plastic frame.

ABS plastic frame for Granular Dacor Carbon (GDC) filter is suitable for incineration or landfill disposal. Cartridge is available with specialty carbons for treating light, molecular-weight contaminants and removal of hydrogen sulfide, ammonia, and formaldehyde. Filter uses premium granulated coconut shell carbon in laminated honeycomb. Low pressure drop makes it suitable for retrofitting. It...

Read More »
Carrier Board connects I/O to CompactPCI systems.
Electronic Boards

Carrier Board connects I/O to CompactPCI systems.

ETX single-board computer carrier board module supports peripheral and network connections, enabling accelerated development of embedded systems. Via miniature connectors, PCI bus, ISA bus and I/O signals such as serial ports, parallel port, USB ports, video and LCD signals, Ethernet, keyboard, mouse and audio interface are brought to baseboard, eliminating need to design special interfaces or...

Read More »
Rejection Filters address SATCOM market.
RF and Microwave Filters

Rejection Filters address SATCOM market.

Series 12086 transmit rejection filters are installed between antenna and LNA in receive segment of satellite earth terminals. They are used in C-band transceiver applications to isolate uplink and downlink signals. Units offer low loss, typically less than 0.04 dB on receive signals, while providing high degree of transmit rejection, ranging from 50 to 80 dB. Construction is 100% dip brazed...

Read More »
LED Holder snaps directly into panel.
Mounts

LED Holder snaps directly into panel.

Model LEDHPM-1 holds T-1 3/4 LED securely while it snaps into board or panel. Part snaps into 0.281 to 0.287 in. diameter hole in panel 0.044 to 0.048 in. thick. Snap-in fingers for panel hold LED in place, so no extra retaining rings are required.

Read More »
Board Stackers offer design flexibility.
Stackers

Board Stackers offer design flexibility.

On .100 in. pitch, single, double and triple row through-hole headers (MTSW Series) and stackers (ZW Series), surface mount board stackers (HW Series) and shrouded headers (ZSS Series) are available for board stacking. For micro pitch, board stackers are available on .8mm pitch (AW Series), 1mm pitch (MW Series), .050 in. pitch (FW Series), .050 in. x .100 in. pitch (DWM Series) and 2mm pitch (TW...

Read More »
Surge Suppressor fits in tiny spots.
Surge Suppressors

Surge Suppressor fits in tiny spots.

Tower version of Model 8R15/8R7.5 stands vertically on 4 x 4 in. desk or floor space, providing easy access to On/Off switch. It has two always on" and eight switched outlets. Surge suppressor handles up to three computing systems or several electronic devices.

Read More »
Emergency Ballast Pack converts fluorescent fixtures.
Ballasts

Emergency Ballast Pack converts fluorescent fixtures.

Compact 200 Series, Models 216, 217, 204SX, 211SX and 215SX allow fixture to provide lighting during normal or emergency conditions. During interruption of line voltage, each automatically switches to emergency mode and provides 90 min of lamp operation via rechargeable NiCad battery. When normal power is restored, integral battery charger returns battery to full charge. Ballasts meet NEC and...

Read More »
Power Connectors handle large electrical loads.
Electrical Connectors

Power Connectors handle large electrical loads.

Amphe-Power Connector Series allows users to increase current load per circuit while reducing total number of circuits. Series consists of Power P-lok, GT Reverse Bayonet, and threaded MS5015 style connectors, all incorporating RADSOK socket system. Size 8 AWG contacts handle currents up to 69 A, while size 4 AWG will handle up to 120 A. Based on industrial standard MIL-C-5015, connectors are...

Read More »
Electronic Sockets

RF Test Sockets keep the pressure on.

Spring-loaded lids on radio frequency (RF) test sockets provide consistent lead pressure. Precise pressure requirements can be met with mix-and-match springs from 1/2 to 25 lbs. Each socket comes with floating leadbacker built into every lid, and lids can be used throughout RF/microwave, automated handling and burn-in/life testing applications. Each socket has Microstrip Contacts, which can be...

Read More »

All Topics