Electronic Components & Devices

Computers

Dual PMC Host Board suits intensive I/O applications.

Single-slot Model PP 310/01x supports 1.6 GHz Intel® Pentium M processor with up to 2 Gbytes 200 MHz DDR ECC SDRAM and 1 Mbyte high-speed L2 cache. It includes dual 64-bit PMC sites with front and rear I/O. Each site supports 3.3 or 5V PCI signaling and is available for user modules, standard PMC, or PrPMC modules. Board supports dual Gigabit Ethernet, PICMG® 2.16, PICMG 2.9, and...

Read More »
Power and Grounding Connectors meet UL and CSA requirements.
Electrical Connectors

Power and Grounding Connectors meet UL and CSA requirements.

PAN-LUG(TM) copper compression lugs and splices meet NEBS Level 3 requirements. PAN-LUG Copper HTAP System features slotted design and snap-on clear cover that allows 360° inspections of crimped connection to assure crimp is complete and correct die was used. Other PAN-LUG products include Copper In-Line Reducing Splices, Copper CTAPs, Lugs for No. 8 AWG - 777.7 kcmil Flex Wire, Lugs for...

Read More »
Strain Relief Connectors provide pullout protection.
Electrical Connectors

Strain Relief Connectors provide pullout protection.

Grip-Tite Connectors help secure and seal cords or cables entering enclosure or cabinet. Two-piece internal design features nylon gripper coupled with neoprene grommet. Body and gland nut are malleable iron with protective zinc electroplate finish. Suited for NEMA 4 enclosures and other wet locations, connectors are rated liquidtight, oiltight, and raintight. Sizes range from Â-½ to 3 in....

Read More »
D-Subminiature Connectors are offered in various styles.
Electrical Connectors

D-Subminiature Connectors are offered in various styles.

Available in solder cup, crimp cable, straight, and 90° PCB styles, ZD Series connectors have stamped contacts with gold flash plating over contact area. High-density D-subs (HDDs) are offered with 15, 26, 44, or 62 contacts and have 5 A current carrying capacity, 20 mohm contact resistance on mated contacts, and -55 to +105°C temperature range. They are suited for use in control and...

Read More »
Electronic Drivers

IGBT Gate-Driver Hybrid provides plug-in solution.

Offered in 90 x 36 mm single-in-line package, 3-phase Model GDBD4410 incorporates noise-immune, pulse-transformer technology to transmit galvanic-isolated pulses to drive 6-pack IGBT inverter modules. Turnkey solution provides 7 gate-drive signals up to ±2 A peak per gate, noise immunity in dv/dt environments exceeding 50 kV/Â-µs, and outputs that provide on-chip generated negative...

Read More »
Test-Lead Components enable CAT III 1000 V safety rating.
Leads

Test-Lead Components enable CAT III 1000 V safety rating.

Do-It-Yourself Test Lead Accessories allow user to build custom test leads with unterminated lengths of up to 50 ft. Wire with silicone and general-purpose PVC insulations are available, along with stackable and right-angle banana plugs. All products are rated at 20 A max. Applications include trailer taillights, control panels, and multi-conductor cable runs.

Read More »
Secondary Side Drivers protect power MOSFETs.
Electronic Drivers

Secondary Side Drivers protect power MOSFETs.

Models LTC3900 and LTC3901 are rectifier drivers that drive two N-channel MOSFETs and accept pulse synchronization from primary side controller via pulse transformer. Both have timer and current sense comparators to protect external MOSFETs during normal and light load operation, power up/down, and when driver supply voltage drops too low. Model LTC3900 is for forward converter topologies, while...

Read More »
Synchro to Digital Converters handle two-speed inputs.
Converters

Synchro to Digital Converters handle two-speed inputs.

Measuring 2.6 x 3.1 x .82 in., single module units convert two speed Synchro or Resolver inputs of 11.8, 26, or 90 V 400 Hz or 90 V 60 Hz into 16 Bit parallel binary outputs representing angle. Speed ratios of 1 x 10, 1 x 18, 1 x 36, 1 x 8, 1 x 16, 1 x 64, and 1 x 128 are available. Converters track rates up to 1,000°/sec with ±.005° accuracy and offer DC velocity output and...

Read More »
Electrical Connectors

SMT Connectors handle high-speed applications.

Modularly-designed, MicroSpeed shielded connector system consists of 2 terminal banks and 2 outwardly-arranged shield plates. Longitudinal pitch is 1.0 mm and transverse pitch is 1.5 mm. Connectors are intended for board-to-board connections with 5 mm circuit board distance. Impedance is 100 ohms for differential signals and 50 ohms for single-ended signals. Applications include telecommunication...

Read More »
Connectors secure perpendicular and co-planar boards.
Electrical Connectors

Connectors secure perpendicular and co-planar boards.

High-speed Series QTS-RA/QSS-RA interfaces, with .025 in. pitch, offer locking-screw options that help prevent accidental un-mating due to racking. Pin counts of 50-200 are available. Horizontal applications perform up to 1.75 GHz in single-ended configuration. Applications include servers, routers, set-top boxes, network systems, switchers, hubs, bridges, industrial computers, test systems, and...

Read More »
Fresh Air Intake Designed to Meet ASHRAE 62.2 standards
Sponsored

Fresh Air Intake Designed to Meet ASHRAE 62.2 standards

Alan Manufacturing has a long history of developing innovative solutions for HVAC applications. With over 1,000 product designs under our belt, we have gained a reputation as the go-to source for HVAC dampers, hardware, duct supports, zone control systems, and much more. Adding to this extensive list of achievements we now announce the release of our new line of Fresh Air Intake products. Designed to meet ASHRAE 62.2 standards, they are the most robust and high-performance product of their kind. See our video to learn more.

Read More »

All Topics