Electronic Components & Devices

Processor provides IC-based motion control.
Computer Processors

Processor provides IC-based motion control.

Available in 1-4 axis configurations, Magellan Motion Processor family control DC brush, brushless DC, microstepping, and pulse and direction motors. They provide profile generation, servo loop closure, PLC-style signal manipulation, and motor signal generation. Driven by host microprocessor, unit offers multi-axis synchronization and 4 selectable profile modes: S-curve, trapezoidal, velocity...

Read More »
Electronic Chips

Traffic Manager Chip has 10, 20, and 40 Gbps switch rates.

TeraPacket(TM) TN9450 combines traffic management on enterprise, metro, and core networks and switching at rates up to 40 Gbps. Working at wire speed, device provides queuing, scheduling, and QoS management at aggregate duplex speed of 40 Gbps and supports 256 ports or channels. It can be used either as 40 Gbps traffic manager or as complete 40 Gbps switch.

Read More »
Fluid Processor suits cleanroom applications.
Handling Equipment

Fluid Processor suits cleanroom applications.

Stainless steel, split-system Microfluidizer® 600 and 700 model series can be set up so that operating assembly is in separate room from processing assembly; one hose, up to 30 ft long, runs through wall to connect separated assemblies. Processor reduces particles to sub-micron or droplet sizes, while intensifier pump drives product stream at velocities and pressures up to 40,000 psi...

Read More »
N-Channel MOSFET suits high-current DC/DC converters.
Transistors

N-Channel MOSFET suits high-current DC/DC converters.

Model STD150NH02L will support drain to source voltage of 24 V and max drain current of 150 A. At these ratings, on-resistance is 0.0035 Ohm. At 10 V, typical RDS(on) is 0.003 Ohm and at 5 V it is 0.005 Ohm. Low gate charge helps reduce switching losses, and low thermal resistance facilitates current handling. MOSFET is manufactured using 0.6 Â-µm process, which utilizes metallization and...

Read More »
Laser Cutting System speeds cutting of plate steel.
Heads

Laser Cutting System speeds cutting of plate steel.

FAST Laser(TM) creates dual-flow zone allowing high oxygen assist gas pressures in tightly defined cut zone established by beam geometry. Accelerated oxygen flow along beam path increases cut speed by fueling exothermic reaction. Laser cutting head Model LH2100(TM) offers 7.5 and 10.0 in. focal lengths, and Model LH2125 adds 12.5 in. focal length option for thicker plate. Optional Mariner(TM) CNC...

Read More »
MOSFET Driver tolerates 100 V transients.
Electronic Drivers

MOSFET Driver tolerates 100 V transients.

Model LTC4440 N-channel 80 V MOSFET driver, housed in SOT-23 and 8-lead MSOP packages, offers peak pull-up output current of 2.4 A and 1.5 ohm pull-down output impedance. Unit reduces MOSFET gate drive fall and rise times to 7 ns and 10 ns, respectively, when driving 1,000 pF loads. Input logic signal is internally level-shifted to bootstrapped supply, which may function at up to 115 V above...

Read More »
Connecting Pins extend life of conveyor-belt splices.
Miscellaneous Fasteners

Connecting Pins extend life of conveyor-belt splices.

Clipper® Duralink(TM) and DuraStainless(TM), for wire-hook splices, feature nylon coating that provides 10x more abrasion resistance compared to nylon-covered pins. Coating lubricity reduces wear on inner radius of fastener loops. Duralink pins, with coating extruded over braided stainless steel cable, provide flexibility to accommodate troughing conveyors or crowned pulleys. DuraStainless...

Read More »
Power Choke offers current ratings from 10-26 A.
Inductors

Power Choke offers current ratings from 10-26 A.

Surface-mount Series FW1405 utilizes rectangular copper wire, edge-wound on thermoset epoxy bobbin base, and high-saturation ferrite core. Base features integral 3-terminal design for optimal part adhesion when soldered to pcb. Inductance values range from 0.40-3.9 Â-µH and operating temperature is -25 to +80°C. Standard packaging is 24 mm tape.

Read More »
Processor Blade supports AdvancedTCA platforms.
Computers

Processor Blade supports AdvancedTCA platforms.

Suited for carrier-grade solutions, ATC-4130 is based on Intel® E7501 Chipset with 400 MHz front-side bus, utilizes 2.0 GHz LV Intel Xeon® Processor, and is compliant with PICMG® 3.0/3.1 specifications for AdvancedTCA platforms. System memory of up to 4 GB is supported via 2 ECC-protected DDR SDRAM modules. Unit uses Pigeon Point's management architecture, and offers 10/100...

Read More »
Fluid Mixer handles demanding applications.
Mixers

Fluid Mixer handles demanding applications.

Series BRM, available up to 200 hp, features AGMA Class No. 10 spiral bevel and helical gear set. Low-headroom, right-angle drive is housed in steel casing, available in 7 different size configurations, and withstands harsh interior and exterior environments. Tapered roller bearings carry rating of more than 100,000 hr, with minimum 1.5 service factor. Drywell construction around low-speed shaft...

Read More »
Cut and Bevel Pipe up to 63" Diameter with a Single Lightweight, Portable Machine
Sponsored

Cut and Bevel Pipe up to 63" Diameter with a Single Lightweight, Portable Machine

CS Unitec is a leader in power tools designed for industrial applications, with products that set the standard for robust performance and industry-leading reliability. Adding to our long list of innovation is a new line of pipe cutting machines. For cutting and beveling pipe up to 2" in thickness and diameters from 12" to 63", no other cutting system comes close. See our video to learn more.

Read More »

All Topics