Electronic Components & Devices

Board-to-Board Connector features scalable one-piece design.
Electrical Connectors

Board-to-Board Connector features scalable one-piece design.

Suited for mobile device manufacturers, Compressive Board-to-Board Connector joins main PCB to gold-plated secondary PCB by compression of contacts. Unit is scalable in number of positions, height, and pitch to optimize design flexibility. Made of thermal plastic and copper alloy, connector features pre-loaded contacts and dimples on contact area. Co-planarity of 0.08 mm over all solder tails...

Read More »
Electrical Connectors

Edgeboard Connector features bottom shielding.

For optimal performance through 18 GHz, V-Bite(TM) RF Edgeboard Connector comes in bottom-shielded female Type N model designed to eliminate inductance by shielding open bottom. Connector snaps onto PCB prior to hand or reflow soldering, and is supported from below and above board to disperse rotational torque relief, minimizing rotational stress on solder area. Offered in impedance of 50 W, Type...

Read More »
Chip Monolithic Ceramic Capacitors target automotive market.
Capacitors

Chip Monolithic Ceramic Capacitors target automotive market.

Measuring 6.1 x 5.3 x 2.8-6.4 mm, KCM series is equipped with metal pins and designed for long-term resilience against substrate expansion and contraction stresses resulting from temperature changes experienced in automotive environments. Ability to withstand vibration and mechanical impact, KCM/KC3 series promotes reliability characteristics. MLCCs offer nominal operating voltages from 25-100...

Read More »
Fiber Optic Modem supports 10/100 Mbps Ethernet.
Converters

Fiber Optic Modem supports 10/100 Mbps Ethernet.

Measuring 4 x 3.6 x 1.2 in., Industrial Ethernet to Fiber Optic Bit DriverÂ-® Model 2151 provides one 10/100 Mbps Ethernet port and 1 Fiber Port, which can be multimode or single mode. Unit offers DIN rail mounting with redundant 10-32 Vdc power input. Housed in IP40 rated enclosure, Ethernet board is conformal coated for environmental protection from dust, dirt, and humidity. Model 2151...

Read More »
Board-to-Board Connector features scalable one-piece design.
Electrical Connectors

Board-to-Board Connector features scalable one-piece design.

Suited for mobile device manufacturers, Compressive Board-to-Board Connector joins main PCB to gold-plated secondary PCB by compression of contacts. Unit is scalable in number of positions, height, and pitch to optimize design flexibility. Made of thermal plastic and copper alloy, connector features pre-loaded contacts and dimples on contact area. Co-planarity of 0.08 mm over all solder tails...

Read More »
Frame Grabbers

DVI/VGA/HDMI Frame Grabber delivers lossless capture.

Able to fit into x4, x8, or x16 PCIe 1.x slot, DVI2PCIe captures video from any single-link DVI, unencrypted HDMI video, VGA, DisplayPort, Mini DisplayPort, Thunderbolt video, or BNC/component video source. Card can capture full HD video at a 30 fps for 1080p video and supports video sources wih resolutions up to 1,920 x 1,200. Capturing video in 100% lossless quality, frame grabber has 128 MB...

Read More »
Frame Grabbers

DVI/VGA/HDMI Frame Grabber delivers lossless capture.

Able to fit into x4, x8, or x16 PCIe 1.x slot, DVI2PCIe captures video from any single-link DVI, unencrypted HDMI video, VGA, DisplayPort, Mini DisplayPort, Thunderbolt video, or BNC/component video source. Card can capture full HD video at a 30 fps for 1080p video and supports video sources wih resolutions up to 1,920 x 1,200. Capturing video in 100% lossless quality, frame grabber has 128 MB...

Read More »
Housings

Del City's AT Series(TM) Sealed Connectors Kit

Milwaukee, WI - Del City's AT Series(TM) Connector Kit is an assortment of connectors and terminals that allow for water-proof connections. Included in the kit are 224 pieces of housings, terminals and wedges intended to handle most repairs. AT Series(TM) connectors are designed with dual seals and ergonomic locking clips. AT Series(TM) housings and wedges are made from a thermoplastic material...

Read More »
Housings

Del City's AT Series(TM) Sealed Connectors Kit

Milwaukee, WI - Del City's AT Series(TM) Connector Kit is an assortment of connectors and terminals that allow for water-proof connections. Included in the kit are 224 pieces of housings, terminals and wedges intended to handle most repairs. AT Series(TM) connectors are designed with dual seals and ergonomic locking clips. AT Series(TM) housings and wedges are made from a thermoplastic material...

Read More »
Electrical Connectors

Plastic USB Connectors survive harsh industrial environments.

The Amphenol USBField range is a pioneer in the field of USB connections for harsh environments. Today, Amphenol extends its range by proposing a plastic version USB called USBAP for industrial markets. Both robust and economical, this new range of products is specially adapted for applications for access points on telecoms equipment, video controls, robotics, and industrial process...

Read More »
Sentry Equipment Introduces New Compact Hygienic Automatic Sampler
Sponsored

Sentry Equipment Introduces New Compact Hygienic Automatic Sampler

As a leader in industrial sampling equipment at Sentry Equipment, our success is built on a history of innovation and designs that epitomize value and efficiency. The new Hygienic Automatic Sampler is another example of our dedication to developing quality engineered products. To learn how this product can streamline the sampling process for dry, free-flowing materials, see our new video.

Read More »

All Topics