Electronic Amplifiers

Electronic Amplifiers

Amplifier Gainblock measures 70 x 40 x 7.5 mm.

Enabled by Mini-DIL un-cooled 980 nm pump module, MiNi Block(TM) u7040 targets 40 Gb/s transport systems in which low-noise optical amplification is required for each channel before 40 Gb/s receiver. Unit offers output power up to 15 dBm and produces 1.2 W thermal dissipation. Available in semi-custom variants to meet specific requirements, amplifier is built using telecom-grade 125 Â-µ...

Read More »
Pallet Amplifier is designed for FM and HDFM radio broadcast.
Electronic Amplifiers

Pallet Amplifier is designed for FM and HDFM radio broadcast.

Featuring 300 W CW output power, 78% collector efficiency, and -40 dB harmonic suppression, Model FM310-108 pallet amplifier is suited for FM transmitter, transposer, and broadcast exciter designs. Available with MRF6V2300NBR1 LDMOS transistor, rugged unit operates from -10 to +60°C. With 23 dB gain, system designers can use low input power of 1.4 W, eliminating one or more gain stages....

Read More »
UHF Power Amplifier operates from 22-32 Vdc supply.
Electronic Amplifiers

UHF Power Amplifier operates from 22-32 Vdc supply.

Employing laterally diffused metal oxide semiconductor device technology, Model US1498 is designed specifically for airborne and fixed location operations. Dual input, single output design provides minimum of 100 W/channel output across frequency range of 290-320 MHz. Packaged in thermally efficient, finned aluminum housing for customer-supplied forced air cooling, device incorporates digital...

Read More »
Electronic Amplifiers

Fiber Optic Amplifiers feature dual digital displays.

Model D2RF series amplifiers feature programming format offering 6 teaching modes including auto teach, zone teaching, and glass teaching mode. They include 2 x 4-digit displays for verification of light received level and threshold level, which also aid in setup and programming of devices. Equipped with selectable one-shot, off-delay, and on-delay timers, units are available in 2 output...

Read More »
Electronic Amplifiers

Op-Amps eliminates EMI-induced errors in analog systems.

Featuring EMI rejection ratio of 120 dB, PowerWise® LMV83x series integrates EMI filters and maintains accuracy of analog systems by reducing effects of RFI. Products also feature 3 MHz unity gain bandwidth while operating on 240 Â-µA supply current, yielding power-to-performance ratio of 80 µA per MHz. All devices - LMV831 single, LMV832 dual, LMV834 quad - minimize need for...

Read More »
Electronic Amplifiers

Audio Subsystem is suited for portable devices.

With 2 stereo single-ended inputs that can be configured as single stereo differential input, Model TPA2050D4 audio subsystem includes stereo Class-D amplifier that provides 1.4 W per channel output drive capability into 8 Ohm loudspeakers with 90% efficiency to extend battery life in portable applications. It also features low-noise stereo DirectPath(TM) headphone amplifier that eliminates need...

Read More »
Electronic Amplifiers

RF Power Detector, Log Amp promote wireless performance.

Integrated crest-factor RF power detection IC, ADL5502, combines rms RF detector and envelope detector. Featuring ±0.1 dB accuracy with crest factors up to 11 dBm, it enables cell phone designers to manage wireless handset power, extend battery life, and process complex 3G/4G signals. Logarithmic amplifier, ADL5513, offers 80 dB dynamic range with ±3 dB log conformance up to 4 GHz to...

Read More »
Electronic Amplifiers

Differential Amplifiers can drive 14- and 16-bit ADCs.

Consuming less than 120 mW of power on single 3.3 V supply, single channel ADA4939-1 and dual channel ADA4939-2 differential amplifiers achieve 82 dB SFDR at 70 MHz. Operating over -40 to 105°C temperature range for both 3.3 and 5 V operation, units feature input voltage noise of 2.3 nV/rt Hz, -3 dB bandwidth of 1.4 GHz, and slew rate of 5,000 V/Â-µS. Model ADA4939-2 can drive dual...

Read More »
Electronic Amplifiers

IC Pair acts as direct conversion receiver solution.

Quadrature demodulator (ADL5380), operating from 400 MHz to 6 GHz, and companion 2-channel digital gain trim amplifier (AD8366) enable and integrate direct conversion radio receivers in cellular 3G/4G and broadband wireless 802.16 applications. With ADL5380, base station receivers can be designed for various cellular and broadband wireless data systems and standards. Features for AD8366 include...

Read More »
Low Noise Amplifiers offer optimal IP3 headroom.
Electronic Amplifiers

Low Noise Amplifiers offer optimal IP3 headroom.

Drawing 425 mA from 12 V supply, Models JCA02-4000, JCA24-4001, and JCA48-4000 feature frequency bands of 0.5-2, 2-4, and 4-8 GHz, respectively. Units offer noise figures under 2 dB up through C-Band, output P1dB levels of +24 dBm, and output IP3 headroom levels of 15 dB or greater above output P1dB compression point. In addition, LNAs deliver saturated output power levels approaching +27 dBm,...

Read More »
Cut and Bevel Pipe up to 63" Diameter with a Single Lightweight, Portable Machine
Sponsored

Cut and Bevel Pipe up to 63" Diameter with a Single Lightweight, Portable Machine

CS Unitec is a leader in power tools designed for industrial applications, with products that set the standard for robust performance and industry-leading reliability. Adding to our long list of innovation is a new line of pipe cutting machines. For cutting and beveling pipe up to 2" in thickness and diameters from 12" to 63", no other cutting system comes close. See our video to learn more.

Read More »

All Topics