Electronic Amplifiers

Electronic Amplifiers

Optical Distribution Amplifiers handle video/audio/data signals.

Pure Digital Fiberlink® 8000 and 8100 Series transmit 1-4 and 2-12 channels, respectively, of any combination of video, audio, and data signals from one-way Pure Digital Fiberlink Transmitters. They transmit to multiple one-way Pure Digital Fiberlink Receivers without degradation to quality of original baseband signals. Both series can receive signals over multimode or single mode fiber at...

Read More »
CMOS Amplifiers suit low power applications.
Electronic Amplifiers

CMOS Amplifiers suit low power applications.

Models LMV321, LMV358, and LMV324 are single, dual, and quad amplifiers, respectively. They consume supply current of 120 microamps max at 2.7 V and typically 100 microamps at 5 V. Units provide rail-to-rail output and offer supply voltage of 2.5-5.5 V. With gain bandwidth of 1.4 MHz at 5 V and slew rate of 1.5 V/microsecond at 5 V, amplifiers are suitable for portable applications such as...

Read More »
Electronic Amplifiers

Amplifier and Transponder simplify network installation.

Model A1070 Erbium Doped Fiber Amplifier consists of variable gain line amplifier with up to 25 db of gain and automatic transient suppression, which minimizes transmission penalties as channels are added/dropped in network. Supporting up to 40 channels at full gain, unit is managed through local serial port, Telnet, or SNMP. Optical transponder A1010 offers 640 km Dense Wavelength Division...

Read More »
Sensor Amplifiers are DIN rail mounted.
Electronic Amplifiers

Sensor Amplifiers are DIN rail mounted.

Sensor Amplifiers offer hi-level output signals, ready for long cable runs and/or direct interface to common PLC interface cards. They provide controlled power to associated sensor and condition sensor's return signal before providing it to output terminals. Relay buffered shunt calibration circuit offers simplified calibration, set-up, and real time circuit verification. Outputs include ±5...

Read More »
Amplifier provides signal gains of 35 dBm.
Electronic Amplifiers

Amplifier provides signal gains of 35 dBm.

Single-Channel C-Band Erbium Doped Fiber Amplifier comes as cooled or coolerless gain block with integrated control electronics that includes laser and TEC driver circuit with alarms and monitors. Amplifier is capable of signal gains up to 35 dBm with noise of less than 4.5 dB and total output power of +10 dBm. Assembly, electrical interface, and included software bundle measures 90 x 70 x 12 mm.

Read More »
Signal Conditioner suits multi-channel applications.
Electronic Amplifiers

Signal Conditioner suits multi-channel applications.

Rack-mounted Model 482B, 8-channel amplifier card communicates with SMART ISOTRON® (IEEE P1451.4 TEDS) accelerometers and provides backwards compatibility for use with IEPE transducers and RCCs. Each card has independent microprocessor and programmable gain of 0-100 with accuracy of ±0.5% at 1 KHz for gains greater than 1. Features include selectable Butterworth 2-pole low-pass filter...

Read More »
Power Amplifier IC suits portable audio applications.
Electronic Amplifiers

Power Amplifier IC suits portable audio applications.

Model FAN7023 monaural, CMOS power amplifier comes in mini SO-8 and SO-8 package. When delivering 1.0 W of continuous RMS power into 8 ohm speaker at 5 V supply, unit typically has 0.1% of THD+N. It operates from 2.2-5.5 V supply, and Power Supply Rejection Ratio is typically 65 dB. With low supply current and shutdown function, as well as low shutdown current consumption of 0.1 microamp, FAN7023...

Read More »
Audio Amplifier Controller delivers 10-50 W power levels.
Electronic Amplifiers

Audio Amplifier Controller delivers 10-50 W power levels.

Acoustar(TM) ZXCW8100, 2-channel, 32-bit, end-to-end digital controller handles digital audio signals sampled at up to 192 kHz. It supports all common digital audio formats from SACD to DTS and produces pulse width modulated left and right channel outputs at frequency of 1 MHz. Amplifier provides dynamic range over 100 dB, completely removing hiss with noise floor of -125 dB. Device ID enables up...

Read More »
Immunity Tester provides complete test report.
Electronic Amplifiers

Immunity Tester provides complete test report.

EM Test Model CWS500D immunity tester contains signal generator, directional coupler, power amplifier, controller, and Windows-based operating software for Automotive, Telecom, and Military applications. Includes GPIB (IEEE 488.2) interface that permits connection of external dual channel power meter for measuring forward power and for monitoring injected RF current. Uses 100 W RF amplifier with...

Read More »
Power Amplifier extends battery life in portable applications.
Electronic Amplifiers

Power Amplifier extends battery life in portable applications.

Dual, fully differential 2 W CMOS Model FAN7031 features 20-pin, TSSOP-EP thermally enhanced package. Integrated, adaptive bias current control circuit decreases crossover distortion. Amplifier consumes 4 Â-µA in shutdown mode over power supply range of 2.7-5.5 V. It allows Single Ended operation for headphone drive. Internal gain adjustment is provided through 2 input pins. FAN7031 is...

Read More »

All Topics

COVID-19 Response Suppliers COVID-19 Response:
Can Your Company Help Provide Critical Supplies?

We are using the power of our platform to aid in the mass shortage of critical supplies. If your company can help provide supplies, capabilities, or materials for products such as N-95 Masks and Tyvek SuitsPlease let us know.

COVID-19 Response Suppliers