Electronic Amplifiers

Filterless Class-D Audio Amp suits portable applications.
Electronic Amplifiers

Filterless Class-D Audio Amp suits portable applications.

From 5 V supply, NCP2820 delivers up to 2.65 W of continuous average power into 4 ohm bridge-tied load (BTL). Under same conditions, output power stage can provide 1.4 W into 8 ohm BTL load with less than 1% total harmonic distortion plus noise. Product has 2.5-5.5 V input voltage range and drives clean audio output. Featuring 90% power efficiency and shutdown current of 0.42 Â-µA, unit does...

Read More »
Wideband Amplifier offers dynamic range up to 80 dB.
Electronic Amplifiers

Wideband Amplifier offers dynamic range up to 80 dB.

With DC-coupled input and rise and fall time of 5 ns, logarithmic wideband voltage amplifier, Model HLVA-100, is suited for measurement of fast and high dynamic pulses. It includes adjustable input range, trimpots, and integrated sample and hold circuit for automated baseline correction of amplifier. Switchable at amplifier or remotely, Model HLVA-100 is laid out in EMI-shielded aluminum package...

Read More »
Amplifiers offer power up to 4,000 W.
Electronic Amplifiers

Amplifiers offer power up to 4,000 W.

Covering 80-1,000 Mhz frequency range, 1,000 W Model 1000W1000C can have power added in 1,000 W increments up to 4,000 W by adding amplifier module and control unit. Model 4000W1000, with 4,000 W of power, includes gain control and internal RF detector that provides output for self-testing or operational modes. It employs push-pull circuitry in all high-power stages to minimize distortion, and...

Read More »
TWT Amplifiers are offered in three 1,500 W models.
Electronic Amplifiers

TWT Amplifiers are offered in three 1,500 W models.

Traveling wave tube (TWT) amps provide RF power for various applications in test and measurement, research and development, and service applications. With modular construction, self-contained, forced air-cooled broadband TWT amps are equipped with front panel digital displays that show forward and reflected output. Models 1500T1G3A, 1500T2G8A, and 1500T8G18 cover respective frequency ranges of...

Read More »
The Next Wave of Intelligent Design Automation
Sponsored

The Next Wave of Intelligent Design Automation

In the amount of time it takes to set up a meeting to discuss just one design, engineers can now explore designs exponentially. Generative design has catalyzed a paradigm shift in product development. This shift not only drastically decreases the time it takes to design a product. It also opens the door to design options that might never have been imagined by engineers on their own.

Read More »
Current Feedback Amplifier operates to 37 V.
Electronic Amplifiers

Current Feedback Amplifier operates to 37 V.

High-voltage Model THS3001HV features slew rate of 6,500 V/Â-µs, 40 ns settling time, 420 MHz bandwidth, and 1.6 nV/rtHz input referred voltage noise. Housed in 8-pin, mini small-outline package with PowerPad®, unit is available in commercial temperature grade from 0-70°C and industrial temperature grade from -40 to 85°C. Applications include test and measurements,...

Read More »
Audio Power Amplifier suits flat panel displays.
Electronic Amplifiers

Audio Power Amplifier suits flat panel displays.

Intended for 27 in. and larger displays, 20 W Class-D Model TPA3200D1 provides both digital interface and power amplifier. Device's 250 kHz switching frequency oversamples audio signal minimum of 10 times. Digital 24-bit I2S or 16-bit right-justified input connects directly to most audio processors. Housed in 44-pin TSSOP package, amplifier includes 3 integrated gain settings, thermal and...

Read More »
Electronic Amplifiers

Instrumentation Amp suits low-voltage applications.

Operating at voltages from 1.8-5.5 V, AD8553 Features offset voltage of 25 Â-µV max, offset voltage drift of 0.1 µV/°C max, and voltage noise of 0.7 µV p-p. Parasitic resistance in series with Vref pin does not degrade performance, allowing unit to attain CMRR performance of 120 dB min @ G=100 without using buffer amp to drive Vref pin. In shutdown mode, total supply...

Read More »
RF Amplifier are suited for low-power applications.
Electronic Amplifiers

RF Amplifier are suited for low-power applications.

With frequency response of 4.0-10.6 GHz, Model 20S4G11 broadband solid-state amp helps satisfy need for low-power, high-frequency applications. Operating specifications include rated power output of 20 W min, flatness of +2.0 dB typ and +3.0 dB max, as well as gain, at max setting, of 43 dB min. Mismatch tolerance is rated at 100% of rated power without feedback, and harmonic distortion is -20...

Read More »
Electronic Amplifiers

Wireless Accessories facilitate enterprise networking.

EliteConnect(TM) 2.4 GHz, 500 mW PoE Amplifier, Model SMCAMP-500G increases signal strength and operating distance of 802.11b/g enterprise access points, bridges, and high-gain antennas. Suited for point-to-point and point-to-multipoint applications, EliteConnect SMCANT-OOM5P Omni-Directional Antenna provides 360° coverage at distances up to 1.5 miles. For building-to-building connections,...

Read More »
Signal Conditioner/Amplifier accepts high level signals.
Electronic Amplifiers

Signal Conditioner/Amplifier accepts high level signals.

With frequency response of 110 kHz, Model A2 features digital control of system instrumentation and monitoring of 10 Vdc analog outputs, both locally on control panel and remotely by Ethernet from PC. Embedded web server is scalable in multiples of 8 channels to maximum of 128. All system, card, and channel settings are accessible using HTTP commands or GUI provided by system. Model A2 is...

Read More »

All Topics