Electronic Amplifiers

Electronic Amplifiers

Wideband Op Amp features input noise of 0.65 nV/sqrtHz.

Available in SOT23-5L or SO-8 package, TSH300 offers bandwidth of 200 MHz at gain of 5 V/V. It operates from 4.5-5.5 V on either single or dual supplies over -40 to +85°C temperature range. With slew rate of 230 V/Â-µ and SFDR of 55 dBc, measured with 10 MHz output sine wave of 2 Vp-p into 100 ohm load, amplifier is suitable as component in A/D converter interface as well as high end...

Read More »
Electronic Amplifiers

Class AB Audio Amplifier measures 1.25 x 1.25 x 0.4 mm.

Offered in Pb-free, 9-bump micro SMD package, LM4995 Boomer® 1.3 W mono Class AB audio amp operates on 5 V supply and is capable of driving 8-ohm speaker load at continuous average output of 1.3 W. It does not require bootstrap capacitors or snubber circuits, is unity-gain stable, and has externally configurable gain. Suited for cell phone handsfree and ringer functions, unit offers power...

Read More »
Electronic Amplifiers

Amplifier Module measures only 7.5 mm thick.

Ultra-thin PureGain 400 erbium doped fiber amplifier module is designed to work within stringent space constraints found in transponder and line card applications. It can be used in pre-amp configuration, which enables high receiver sensitivity without trans-impedance amplifier, or booster configuration, which enables high launch power in advanced transmitter designs. Utilizing standard optical...

Read More »
Electronic Amplifiers

Wireless Access Solutions expand network capacity/coverage.

Featuring microcellular coverage range, wall-mountable BTS 3030 has zero footprint that can be used to address demands of capacity hot spots or fill coverage holes. Product minimizes number of BTS required to cope with increasing network usage. Scalable CDMA radio module, MFRM3, boosts capacity in existing Indoor Metro Cell and Compact Metro Cell Outdoor base stations. Both products allow...

Read More »
Amplifier captures and holds signals and pulses.
Electronic Amplifiers

Amplifier captures and holds signals and pulses.

Providing stand-alone Sample-Hold solution, Model SHM-50 features signal bandwidth of 70 MHz and is available in through-hole or surface-mount, 8-pin mini-DIP package. Complete sample-hold circuit contains precision MOS hold capacitor and feed-through attenuation of -78 dB. FED input amplifier design allows acquisition time of 40 ns for 2 V step to ±0.01% accuracy, and 50 ns to...

Read More »
Electronic Amplifiers

Power Amplifier targets 3G wireless networks.

Utilizing adapted analog pre-distortion linearization technology, Multi-Carrier Power Amplifier enables amplification and integration of multiple carrier signals into single antenna on base stations. It features modular design for various power levels and frequencies, supports up to 4 WCDMA carriers, and provides greater than 18% efficiency.

Read More »
Electronic Amplifiers

AR Worldwide "S" Series Amplifiers Ideal for Testing WiMAX Output Devices

Tests Show That These AR Worldwide RF/Microwave Instrumentation Amplifiers Reproduce Signals With Remarkable Fidelity Souderton, PA - 4/4/06 - A much larger signal than the typical Vector Signal generator can produce is needed for testing many WiMAX output devices. Therefore an amplifier is needed to produce these signals. The amplifier must have sufficient power to do the testing, but it must...

Read More »
Transimpedance Amplifier conforms to RoHS standards.
Electronic Amplifiers

Transimpedance Amplifier conforms to RoHS standards.

Available in SOP16 and QSOP16 packages, MTI04CS/CQ signal amplifier integrates 4 channels on single chip, enabling signal preparation for 3-range color sensors, including reference diode, in one component. Transimpedance can be set at 8 different levels to accommodate application requirements. Operating temperature range is -40 to +125°C, and lowest current measurement range is 25 nA....

Read More »
Measurement Amp suits electrically demanding environments.
Electronic Amplifiers

Measurement Amp suits electrically demanding environments.

Multi-channel carrier-frequency amplifier system, ML455, has signal bandwidth of up to 1,000 Hz that makes it suited for measuring mechanical quantities. Designed for multi-functional use, product suppresses interference such as voltage noise and eliminates drift effects resulting from thermal voltages. Transducer channels can be configured individually for each sub-channel, and measurement...

Read More »
Op Amps suit handheld and battery-powered applications.
Electronic Amplifiers

Op Amps suit handheld and battery-powered applications.

Housed in tiny DFN package, Models LT6001 and LT6002 are 1.8 V dual and quad operational amplifiers that draw 13 Â-µA each. Input offset voltage is 500 µV max at 25°C with max drift of 5 µV/°C over temperature. Inputs and outputs feature rail-to-rail operation. Model LT6001 also includes shutdown pin, allowing current consumption to drop to 1.5 µA max when...

Read More »

All Topics