Electronic Amplifiers

Zero-Crossover Op Amp suits battery-powered applications.
Electronic Amplifiers

Zero-Crossover Op Amp suits battery-powered applications.

Featuring single-input-stage architecture that delivers offset voltage of 750 Â-µV over entire rail-to-rail input range and CMRR of 100 dB min, OPA369 achieves rail-to-rail performance without input crossover. This solves design problem of input offset distortion due to change in common mode voltage. Supplied in SC70 package (single), product features 1 µA quiescent current and...

Read More »
Electronic Amplifiers

Instrumentation Amplifier has rail-to-rail I/O capability.

Offered as single-chip, 6 x 9.9 mm QSOP solution, Model ISL28470 quad instrumentation amplifier delivers offset voltage of ±150 Â-µV and typical CMMR (common mode rejection ratio) of 110 dB. It is optimized for low 2.4-5 V single supplies and is capable of swinging above positive supply rail and to 10 mV below negative supply. Unit simplifies designs for applications that require...

Read More »
Electronic Amplifiers

Intersil Achieves 1nV Noise Performance in a Single-Supply Op Amp

Intersil's ISL28x90 and ISL28x91 Deliver the Industry's Best Noise and Total Harmonic Distortion Performance among Rail-to-Rail Output, Single-Supply Precision Op Amps MILPITAS, CA, July 02, 2007 - Intersil Corporation (NASDAQ Global Select: ISIL) today announced the release of the ISL28190, ISL28290, ISL28191 and ISL28291. These devices, part of Intersil's pinPOINT(TM) Precision Analog product...

Read More »
Electronic Amplifiers

Op Amps/Comparators feature low supply current consumption.

With single-supply input voltage range of 1.8-5.5 V, rail-to-rail I/O operational amplifiers and comparators are suited for low-power precision applications running off two 1.5 V alkaline batteries. Model ISL28194 offers supply current rating of 330 nA (typ) and 450 nA (max), while Model ISL28195 consumes 1 Â-µA of supply current. Models ISL28197 and ISL28196 comparators typically consume...

Read More »
Electronic Amplifiers

Powerwave Introduces 1900MHZ Tower Mounted Amplifier

Designed to enhance coverage and improve the uplink signal quality for RET antennas in UMTS and AWS networks, the TMA is also AISG compatible CTIA WIRELESS 2007, ORLANDO, Fla., Booth #2163, March 28, 2007 - Powerwave Technologies, Inc. (NASDAQ:PWAV), a global source for end-to-end wireless infrastructure solutions, today expanded its growing line-up of tower mounted amplifiers (TMAs) with the...

Read More »
Electronic Amplifiers

Powerwave Extends Coverage of High Power Wideband Radio Head to Support Advanced Wireless Services Frequency Band

Combining Exceptional Reliability with High Performance, the Wideband Radio Head is Ideal for Deployments in Dense Urban Areas CTIA WIRELESS 2007, ORLANDO, Fla., Booth #2163, March 27, 2007 - Powerwave Technologies, Inc. (NASDAQ:PWAV), a global source for end-to-end wireless infrastructure solutions, announced that its high power Wideband Radio Head (WRH) now offers support for the Advanced...

Read More »
Electronic Amplifiers

Toshiba to Showcase C-, X- and Ku-band GaAs FETs, X-Band GaN HEMT for Radar and Medical Applications, and RF Devices for Two-Way Radios and DTTV Tuners at MTT-S

Microwave, RF And Small Signal Devices Will Be On Display At IEEE MTT-S International Microwave Symposium, June 5-7 In Hawaii HONOLULU, Hawaii, June 5 / - Toshiba America Electronic Components, Inc. (TAEC)* will feature an extensive array of C-, X- and Ku-band gallium arsenide (GaAs) field effect transistors (FETs) developed by Toshiba Corp. (Toshiba) as well as a broad line-up of radio frequency...

Read More »
Electronic Amplifiers

PGAs offer 4 levels of internal frequency compensation.

Models LMP8100A and LMP8100 programmable gain amplifiers (PGAs) are built on 33 MHz CMOS input, rail-to-rail I/O operational amplifier with typical open-loop gain of 110 dB. Model LMP8100A delivers 0.03% gain accuracy using software adjustable gain (in 1 V/V increments) from 1-16 V/V over full industrial temperature range of -40 to 125°C, while Model LMP8100 semi-precision grade PGA...

Read More »
Operational Amplifier requires only 1.6 mA supply current.
Electronic Amplifiers

Operational Amplifier requires only 1.6 mA supply current.

Operating from single 2.7-5.5 V supply, Model AS1710 can swing to within 100 mV from rails while sinking or sourcing 50 mA of output current. Large short-time loads are covered with peak current of greater than 200 mA. Available in 6-pin SC70 package for -40 to +125°C operating environments, device features 10 MHz unity gain bandwidth and 10 V/Â-µs slew rate. It is suited for headphone...

Read More »
Electronic Amplifiers

Linear Power Amplifier is designed for PHS applications.

Supplied in Pb-free 3 mm 12-lead PQFN package, M/A-COM MAAP-000082 is suited for space-restricted PHS (Personal Handy-phone System) applications that require high gain and efficiency. This 1.9 GHz, 3-stage power amplifier is equipped with ESD protection and withstands electrostatic discharges up to 1,000 V without performance degradation. Consuming 200 mA of current, it provides 21 dBm of linear...

Read More »
Paratherm™ HR Heat Transfer Fluid: Higher Temperature Stability Leads to Longer Fluid Life
Sponsored

Paratherm™ HR Heat Transfer Fluid: Higher Temperature Stability Leads to Longer Fluid Life

For the ultimate in heat transfer fluid performance, Paratherm offers HR Heat Transfer Fluid that is engineered specifically for closed loop liquid phase heating. When it comes to characteristics such as thermal stability and fluid degradation, Paratherm HR leads the industry in value and performance. See our video to learn how Paratherm is raising the bar for heat transfer fluids.

Read More »

All Topics