Electrical Sensors / Detectors / Transducers

AC Current Sensor requires no external power.
Electrical Sensors / Detectors / Transducers

AC Current Sensor requires no external power.

Loop powered DCSA Series linear output current transformer provides output that is directly proportional to rms ac current passing through external LCSC10T12 toroidal sensor. Output can be 4-20 mA, 1-5 Vdc, or 2-10 Vdc. It is available in ranges of 0-5, 0-10, and 0-50 A, making it suitable for measuring current draw on motors, fans, lamps, heaters, solenoids, and valves. The 0-5 A range allows...

Read More »
Current-to-Voltage Sensor is designed for PCB mounting.
Electrical Sensors / Detectors / Transducers

Current-to-Voltage Sensor is designed for PCB mounting.

Model EX9PC500 measures AC currents up to 50 A, 47 to 400 Hz. Toroidally wound precision coil has 0.31 in. dia sensor coil. Typical maximum voltage outputs are 440 mV @ 50 A with 10 ohm burden resistance and 660 mV @ 30 A with 24 ohm burden resistance. Low loss materials offer linearity of 3% or better over temperature range. Dimensions are (HxWxL) 31.2 x 17.2 x 27.2 mm. Sensors are mounted using...

Read More »
Sensor offers rugged front-face material.
Electrical Sensors / Detectors / Transducers

Sensor offers rugged front-face material.

WeldGuard Sensor is available in AC/DC ferrite core with WFI, DC U-prox®, and extended ferrite core with 2- and 3-wire DC. Front face material lasts 13 times longer than standard sensor face materials. Barrel is either stainless steel or Teflon® coated. Sensor comes in 8, 12, 18, and 30 mm barrel sizes and cube style CA40 (40 mm cube). It is suitable for resistance welding in...

Read More »
Current Transducer offers closed loop control.
Electrical Sensors / Detectors / Transducers

Current Transducer offers closed loop control.

DCSA Series loop powered, linear output current transformer provides output directly proportional to RMS AC current passing through external LCSC10T12 toroidal sensor. It provides either analog current or voltage: 4 to 20 mA, 1 to 5 Vdc, or 2 to 10 Vdc. Each unit is factory calibrated for monitoring (with LCSC10T12) 0 to 5, 0 to 10, 0 to 20, or 0 to 50 A. Transducer senses current draw on...

Read More »
Electrical Sensors / Detectors / Transducers

Isotropic Analyzers check magnetic and electrical fields.

Model EFA-200 and EFA-300 analyze low-frequency magnetic and electrical fields to determine safety or potential for harm from high-voltage utility lines and industrial equipment such as resistance welders. Analyzers use Shaped Time Domain (STD) technology to measure in low frequency range of 5 Hz to 32 kHz. They calculate and display field strength levels as percent of industry or government...

Read More »
Current Sensor is self-powered.
Electrical Sensors / Detectors / Transducers

Current Sensor is self-powered.

TCS Series Go/No Go Sensor/PLC interface can be directly connected to PLC's digital input module or to load rated up to 1 A. It can detect overcurrent or undercurrent events, and signal PLC or switch load device to ON or OFF. Onboard toroidal sensor monitors current flow through ac loads up to 50 A steady, 300 A inrush. TCS Sensor is available with adjustable or factory-fixed actuation point.

Read More »
Plug-in Transducers reduce installation time.
Electrical Sensors / Detectors / Transducers

Plug-in Transducers reduce installation time.

786 Series transducers can convert 0-10 V or 4-20 mA signals into isolated 0-10 V, 0-20 mA, or 4-20 mA signal with isolation rating of 4kV. It can be plugged directly onto terminal block assembly using base receptacle blocks that are 15, 20, or 25 mm wide. Modules are protected against mismating and can be replaced in single operation during maintenance without affecting wiring. Touchproof test...

Read More »

All Topics