DIN-Rail Power Supply offers 85% efficiency.
Part No. 787-912 2 Amp/24 Vdc switch-mode power supply provides output power of 48 W and universal input voltage of 85 to 264 Vac. Output is electronically protected against short circuits and is equipped with automatic restart. Unit has been tested and approved to UL 1950, CAN/CSA C 22.2 No. 950-95 and IEC/EN 60 950, and meets EMI suppression requirements of EN 50 022 class B. Ambient...
Read More »Fieldbus Modules optimize HART field device potential.
I/A Series Fieldbus Modules enables users to continuously access real-time field device diagnostics and asset management information directly from workstations or PCs. Fieldbus Module channels provide 4-20 mA analog signals and HART digital signals. Modules feature 8 channels, each with its own HART modem; 100 millisecond response times; and up to 4 secondary variables per channel. Modules can be...
Read More »
HART Module allows more variables from existing devices.
Compact DIN-rail mount HIM Smart HART Loop Interface and Monitor obtains up to 3 additional analog process measurements from smart HART multivariable mass flow, level, pressure and pH transmitters. Using HART digital data that rides on 4-20 mA current loop, module breaks out signals representing any combination of transmitter's primary, second, third, or fourth measurement variables. Dual alarm...
Read More »
Snap-On Connectors rated for 500 Vrms, -65 to +165 deg C.
Mini-SMB 75 ohm connectors deliver dc to 4 GHz speed for broadband wireless applications. Connectors comply with MIL-STD 348 and meet Mil-c39012 requirements. Series includes straight RSB-200-1-17 and right angle RSB-21-0-1-179, crimp plugs for RG-179/U cable, vertical and right angle PCB plugs and jacks, and straight RSB-220-1-179 and bulkhead RSB-221-1-179 crimp jacks for RG-179-U cable. All...
Read More »
Rack Systems Done Right: A Hands-On Guide to Reaping Maximum Benefit from Design Review
Learn how to reap the maximum benefit from design review in our whitepaper.
Read More »
Control Transformers work with relays and solenoids.
CPT series has 240/480 Vac and 50/60 Hz primary voltage, and 120 Vac secondary voltage. Transformers maximize inrush capability and output voltage regulation when electromagnetic devices are used. Made of Mylar, Nomex, and other materials, they electrically insulate turn-to-turn windings, layer-to-layer windings, primary-to-secondary windings, and ground. Transformers are vacuum impregnated with...
Read More »Connector carries 1.5 amperes for wire harnessing.
Mini MiII(TM) 1.25 mm pitch connector system is available in wire-to-board and wire-to-wire configurations in 2 to 20 circuits for single row and 10 to 40 circuits for dual row. Single row IDT receptacle has guide slots to facilitate wire placement. Side ribs provide polarization and lock into clip for dual-row configurations. Header options include single or dual row, SMT or through-hole, and...
Read More »
Instrumentation Fittings handle high pressures.
MPI(TM) connectors operate at pressures of 6,000 to 15,000 psi, making them suitable for equipment used to operate feed lines, processing lines, and other systems within industrial labs. Four-part fittings can be used on 316 stainless-steel, cold-drawn, 1/8 hard, unannealed tubing or thick-walled, annealed, instrumentation-grade 316 tubing, and are available for tubing ranging from 1/4 to 1 in....
Read More »
Inverter powers automotive LCDs.
Fully encapsulated P44W DC-AC inverter offers starting voltage of up to 3,000 Vrms. It provides up to 15 watts of output power, runs at up to 9 mils boost current for quick warm-up in cold starts, and performs over operating temperature range of -30 to 85Ã-
Read More »
DC Motors have skewed armatures to reduce cogging.
LO-COG Series 8690(TM) 26mm brush-commutated motors are available in lengths of 1.798, 1.923, and 2.173 in., and provide continuous torque output up to 3.17 oz-in, peak torque up to 20 oz-in, and speeds up to 9,000 rpm. They have two-pole permanent magnet stators and diamond-turned commutators for maximum brush life. Options include optical encoders, custom cables, shaft modifications,...
Read More »
Drum Motor meets MHSA requirements.
Explosion proof 30 hp motor provides safe operation when driving belt conveyors in applications that have potential for fire or explosion, such as mining, feed and grain, sugar mills, and fertilizer plants. Low-profile, 12.5 in. dia motor has heavy-duty bolts; secondary o-ring seal for complete hermetic sealing; standard face width of 51 in.; and cast iron shell, shaft, and end cap. Drum speed is...
Read More »
Don't Let Your Money Drain Down the Hole...Drill Steel with Euroboor
As a globally recognized manufacturer of industrial grade portable tools, Euroboor is at the forefront of drilling and cutting technology. Our reputation as an industry leader is built on robust products that fit a wide range of industrial cutting and drilling applications. See our video to learn more about all of our quality products.
Read More »
