Electrical Equipment & Systems

Optocouplers are available in tape and reel configuration.
Electrical Isolators

Optocouplers are available in tape and reel configuration.

The half-pitch mini-flat package, which includes HMHA281, HMHA2801, and HMHAA280 optocouplers, features 4 surface-mount leads on 0.05 in. spacing, and has 61% smaller footprint than a 4-pin dual inline surface-mount package. Optocouplers consist of a single gallium arsenide infrared emitting diode (dc input), which drives a silicon phototransistor. Applications include telecommunications, power...

Read More »
Wall Box Locator ensures correct height and alignment.
Electrical Boxes

Wall Box Locator ensures correct height and alignment.

Mount-it Wall Box Locator helps contractors and installers properly and consistently align electrical boxes in new construction, or co-locate telephone/data boxes next to electrical boxes. To use, attach unit to piece of standard 1/2-in. EMT conduit, adjust thumb screws to set depth and height, attach electrical box, align it with stud, and secure in place. It works with plastic or metal, single-...

Read More »
Cord Connector allows hot swaps and streamlines wiring.
Electric Wire, Cable and Cable Assemblies

Cord Connector allows hot swaps and streamlines wiring.

Model 4730 cord connector allows hot swapping of power supplies to backplane or rear enclosure. Connector has IEC C20 inlet on one side and IEC outlet on other, so it is not necessary to unplug supply when changing it. Power cord remains while supplies are swapped. Module can be inverted and used to fit male or female connection on either side, depending on configuration. Single-piece module...

Read More »
Power Supplies

Power Supplies are designed for 600 watt applications.

EK Series Power Supplies offer voltage range from 1 to 60 kV in 3.5 in. high rack mount units. They feature air-insulation technology, where air is used as primary dielectric medium rather than silicon rubber, epoxy or oil. Arc sensing and quench circuitry suppress arcing conditions that can occur regularly in high voltage applications, and provide safety and protection for power supply and...

Read More »
Switches are suitable for hand-held electronic devices.
Switches

Switches are suitable for hand-held electronic devices.

Toggle, rocker and slide switches includes miniature, sealed, and subminiature versions. They feature choice of actuators, bushings, and mounting configurations for panel or PCB mounting. Available with silver or gold contacts, switches can be used in power or low level, dry circuit applications. Toggle, rocker and slide switches meet requirements for markets including: test and measurement...

Read More »
Connectors are available in threaded mate or snap-on.
Electrical Connectors

Connectors are available in threaded mate or snap-on.

SMB/SMC Series Subminiature Coaxial Connectors are machined from brass, gold plated to resist corrosion, and have beryllium-copper female contacts and Teflon® insulators. Providing service life of 500 matings, 50 Ohm connectors are rated for 750 Vrms dielecric withstanding voltage and operating temperature from -65°C to +165°C. Frequency range is 0 to 4 GHz for SMB Series and 0...

Read More »
Electrical Connectors

Card Connector supports 10 Gbyte Ethernet standard.

70-pin pcb-mounted edge card connector supports 10 Gbyte family of Z-axis pluggable transceivers. It offers alignment posts for stable placement on pcb and standoffs for pcb post-solder cleaning. SMT design provides option for connector placement on either side of pcb. Connector will support all of transceiver variants noted in MSAs (850 Nm serial, 1310 Nm serial, 1310 WWDM and 1550 serial...

Read More »
One-Handed Clamp uses self-restraining technology..
Clamps

One-Handed Clamp uses self-restraining technology..

Adelok® helps assemble clamped components by holding itself closed and in place during installation. It is suitable for rapid clamp assembly and improved stacking methods for fluid lines and hoses, wire bundles, power cables and fire detection sense lines. Juggling of fasteners, standoffs, washers, ties and grommets is eliminated. Clamp can handle payloads of 0.062 to 3.50 in., and can be...

Read More »
Plug-in Transducers reduce installation time.
Sensors / Detectors / Transducers

Plug-in Transducers reduce installation time.

786 Series transducers can convert 0-10 V or 4-20 mA signals into isolated 0-10 V, 0-20 mA, or 4-20 mA signal with isolation rating of 4kV. It can be plugged directly onto terminal block assembly using base receptacle blocks that are 15, 20, or 25 mm wide. Modules are protected against mismating and can be replaced in single operation during maintenance without affecting wiring. Touchproof test...

Read More »
Transformers operate at 90% efficiency,
Transformers

Transformers operate at 90% efficiency,

High efficiency R-Core transformers have silicon steel cores with two matched bobbins on each side that cancel each other's magnetic flux field, so countermeasures to reduce leakage flux are not needed. Transformers are 30% smaller, 30% thinner and 40% lighter than EI type transformers. Applications include office, A/V, CATV, and electronic equipment. Sizes are available from 5VA to 1000VA.

Read More »
How SpinSelect Can Save You Time and Money
Sponsored

How SpinSelect Can Save You Time and Money

Thanks to the unique SpinSelect™ Multi-Pocket selectable quick change tool holder, it's time to rethink the range, complexity and volume of parts that your lathe can produce. Our Spin-Select™ tool was created to increase productivity and consistency by decreasing downtime associated with lathe cutting tool and insert setups or changeovers. This product is a game-changer for the industry and we're pleased to show you why.

Read More »

All Topics