Electrical Equipment & Systems

Power Quality Monitoring AFE conserves development time.
Circuits

Power Quality Monitoring AFE conserves development time.

Integrating embedded power quality algorithms, 7 ADCs, high-end reference, and flexible DSP core, ADE9000 integrated polyphase analog front end (AFE) enables designers of power quality monitoring solutions to measure and analyze pollution in order to prevent disruptions and long-term damage (primarily for 3-phase power meters). This integration simplifies additional complex algorithm programming...

Read More »
Electric Wire, Cable and Cable Assemblies

CAMI Research, a WHCC Top Product Winner, Reports Milestone Continuity Measurement

CAMI Research Inc. (Acton, MA), a 2015 Wire Harness Cable Connector Top Product winner, reports that a customer has successfully tested simultaneous, multipoint continuity in a two-mile long, multicore cable (rated at 10Ω/1000ft) using a CableEye M3UH tester. Overview Priced in the low thousands range, the test has more traditionally been carried out with testers x10 more expensive. New to the...

Read More »
Switches

Peregrine Semiconductor Wins 2016 ECN IMPACT Award

UltraCMOS® PE42723 High Linearity RF Switch Named a Market Disruptor SAN DIEGO, Oct. 13, 2016 -- Peregrine Semiconductor Corp., founder of RF SOI (silicon on insulator) and pioneer of advanced RF solutions, announces that the UltraCMOS® PE42723 high linearity RF switch has won an ECN IMPACT Award in the market disruptor category. In addition, the PE42723 switch was named a finalist in...

Read More »
Switches

Standex- Electronics to Exhibit Sensors and Magnetics at Electronica 2016

VISIT STANDEX-MEDER AT HALL B1, BOOTH 516 (MAIN BOOTH) FOR REED BASED TECHNOLOGY AND HALL A2, BOOTH 501 FOR MAGNETICS TECHNOLOGY SINGEN, GermanyÂ- - August 31, 2016 - Standex-Meder Electronics, a leading manufacturer of precise, reliable, and long-lasting sensors and magnetic components will highlight its diverse product line at the electronica 2016 show in Munich, Germany. This...

Read More »
IMPULSE's HiPIMS Power Supply feature remote control options.
Controls and Controllers

IMPULSE's HiPIMS Power Supply feature remote control options.

Offered in Single and Dual configurations, the IMPULSE’s HiPIMS Power Supply gives 2kW output. Ideally used in process development and RD applications, HiPIMS' dual configuration powers 2 independent sources of up to 2kW each. Units can be set for either “master” or “slave” mode to run 4kW into a single source. Using the Dual option, the DC bias option can be set. Power supply...

Read More »
Can Stack Linear Actuators offer max holding force of 50 N.
Motors

Can Stack Linear Actuators offer max holding force of 50 N.

Featuring 7.5° step angle that provides fine incremental movement, 20 mm Series 20DBM is suitable for electronic pipettes, medical and non-medical analyzers, XY stages, and valve actuators. Customizable linear stepper motors are powered by high-energy neodymium magnets, optimized electromagnetic circuit, and bearing preload design. RoHS compliant products are available in Captive and...

Read More »
TRUMPower's TPMS-700W ATX PC Power Supply feature overvoltage and overcurrent protection.
Power Supplies

TRUMPower's TPMS-700W ATX PC Power Supply feature overvoltage and overcurrent protection.

Medically approved,Â- TPMS- 700W ATX PC power supply complies with ATX12V standards and 80+ Bronze high efficiency. With the total output current at 50A, and DC voltage outputs and maximum loads of +3.3V/24A, +5V/30A, TPMS-700 comes with 20+4 pin ATX motherboard connector, 4-pin Molex and SATA power connectors. At full load, MTBF of the unit is >146K hours. Unit features low ripple...

Read More »
BEI Kimco's Brushless Motors Meet Centrifuge Requirements for Reliable, Quiet Operation
Motors

BEI Kimco's Brushless Motors Meet Centrifuge Requirements for Reliable, Quiet Operation

VISTA, Calif.,Oct. 4, 2016 - BEI Kimco has met the high performance motor requirements for laboratory centrifuge machines. Centrifuges are used in biology, chemistry and hospital labs to rapidly spin and separate liquid samples into layers for analysis. These machines have varying requirements in motor functionality and size, as well as speeds that can range from just a few thousand RPM to higher...

Read More »
Switches

Power Supply Distribution Switch separately controls 4 lines.

Enclosed inÂ- all-metal chassis that provides EMI/RFI shielding, Model 4423 lets user provide power to any or all of 4 outputs via internal power supply. On/Off rocker switch for each channel controls power output, and each of 4 DC supply voltage lines features protection via fuse: 15 A fuse for +60 Vdc power supply, 30 A fuse for +28 Vdc power supply, and 10...

Read More »
Cyanoacrylate Fuming Chamber safely develops latent fingerprints.
Environmental Chambers

Cyanoacrylate Fuming Chamber safely develops latent fingerprints.

Offered in 24, 30, 48, 60, and 72 in. models, Safefume™ safely develops latent fingerprints using ethyl cyanoacrylate (CNA) vapor in controlled environment. Tamper-resistant compartment helps maintain chain of custody, while Air Science Multiplex™ ductless filtration system as well as design and construction features protect personnel during use. Other features include automatic...

Read More »
Neagle Choice, LLC Announces New Available Services
Sponsored

Neagle Choice, LLC Announces New Available Services

Neagle Choice has long been known as a quality source for commercial sewing, printing, die cutting, and the manufacturing of a wide range of custom products. Enhancing our service capabilities has been the key to our success, and has driven our growth into many new and exciting markets. Continuing on this trajectory, we now offer precision laser cutting and etching, adding to our long line of manufacturing services. See our video to learn all about it.

Read More »

All Topics