Dynamic Probe helps debug FPGAs.
Model B4655A interacts with on-chip virtual probing technology, enabling logic analyzers to measure up to 64 internal FPGA signals for each debug pin. Engineers can select groups of internal signals to probe without requiring design recompiles. State and timing analysis modes allow designers to look at single circuits or correlate multiple circuits. Probe provides mapping of internal signal names...
Read More »
Probe enables single-ended or differential measurements.
When InfiniiMax 1130A 1.5 GHz differential probe is paired with Infiniium mixed signal and digital signal oscilloscopes, system validates and verifies performance of high-speed digital product designs. Controlled transmission-line probe heads provide flat frequency response over entire bandwidth. Resistor tip technology compensates for inductance and capacitance. Variable span between signal tips...
Read More »
Oscilloscope Probe offers x10 fixed attenuation.
Model CT3133RA features 2 adjustment caps for low- and high-frequency compensation, replaceable gold plated tip, and snap-locking sprung hook that provides solid, positive connection. When BNC actuating pin makes contact with actuation pad, scope automatically detects x10 attenuation setting and adjusts scale readout accordingly. Unit meets IEC 61010-031 600V CATI, has 350 MHz bandwidth and 1.0...
Read More »
Connectorless Probe reduces capacitive loading by 80%.
Model E5394A soft touch probe enables direct connection from probe to targets on PCB without use of adapter. In connectorless probing applications, array of probe pads are used for validating digital designs to help streamline design process. Single-ended, 34-channel probe is compatible with all Agilent logic analyzers that use 40-pin connector interface. Product uses micro spring-pin technology...
Read More »
Polymer Protection For Optical Fiber
To learn more about the challenges your optical fibers face, and which polymers are best to protect them, download this white paper.
Read More »
Flexible Current Probes fit into tight spaces.
FlexProbe® Models 24-3001 and 24-3002 consist of AC current-measurement probes that plug into digital multimeters, oscilloscopes, and power recorders. Model 24-3001 is composed of flexible sensor and electronic module with 14 in., double-insulated cable, while Model 24-3002 has flexible sensor and electronic module with 4 mm safety banana jacks with Â-¾ in. spacing. Measuring 24 in....
Read More »
Probing Station verifies design of printed circuit assemblies.
Huntron Access, when coupled with National Instrument's Labview, can integrate with general purpose ATE measuring equipment. Open-architectured, automated probing station delivers accuracy and performance of ProTrack probers with freedom to use additional general-purpose test equipment. It is suited for applications where circuit card is in powered up state.
Read More »
Oscilloscope Probe suits electronics testing and service.
Model 6731 Differential Oscilloscope Probe conducts safe differential measurements. Suited for making floating voltage measurements while operating general-purpose oscilloscopes, product uses built-in differential amplifier to safely convert and scale floating signal to low-voltage signal referenced to earth ground. Probe offers 1000 V peak differential input voltage with 600 V CAT III max...
Read More »Probe Head offers 7 GHz differential SMA capabilities.
InfiniiMax Model E2695A is offered with 3 serial bus validation and compliance testing capabilities for 6 GHz Infiniium real-time oscilloscope. Probe capabilities provide differential SMA connections using one scope channel. Model E2688A Serial Data Analysis/Mask Testing with Clock Recovery package validates serial bus designs during development, performs mask testing, and characterizes serial...
Read More »
PC Oscilloscope Adapter needs no power supply.
Dual channel, 12-bit Model DS2200C samples at rates to 200 ksample/sec. Digital sampling oscilloscope adapter connects to USB port of any computer and fits in laptop carrying cases along with 2 optional probes. EasyScope software, provided with DS2200C, provides front panel appearance for changing of settings. Software also saves screen settings when quitting program. FFT button shows frequency...
Read More »
Insulation Piercing Probe tests in hard-to-reach locations.
Offered in 12 and 24 in. lengths, Model 6580 has heat/burn-resistant Teflon® tubing. Suitable for measurement applications up to 60 Vdc, test probe incorporates spring-loaded wire locator clamp and screw-in point. Piercing probe allows user to provide pressure needed to penetrate hard or soft insulation on wire from 0.060-0.200 in. dia. Hardened steel piercing point is removable for...
Read More »
Basalt America Announces Stronger, Lighter, and Corrosion-Free FRP's (Fiber Reinforced Polymers)
Fiber Reinforced Polymers (FRP), represents a truly groundbreaking advancement in structural reinforcement. Lightweight, strong, and green, they are changing the way the construction industry thinks about rebar. Unlike steel, FRPs don't rust and are far stronger than standard rebar. To learn why Fiber Reinforced Polymers are poised to change the way the world builds, see our video.
Read More »
