New Electric Cable Assemblies Products

Cordsets have stainless steel coupling nuts.

Picofast Cordsets, with 316 stainless steel coupling nuts, withstand wash-down environments and are suitable for food industry applications, or any place caustic materials are used. Hex design, with no knurling, allows easy cleaning. Units are rated to IP 68 and can withstand 1200 psi applications with water, detergents, and surfactants. They have M8 thread and will mate with any quick-disconnect...

Electric Cable Assemblies

Flexible Coaxial Communications Cable is weather-resistant.

With greater than 90 dB shielding, low loss, 50-Ohm cintru(TM) cable operates over frequency range of dc to 6 GHz, depending on connector type. Broadband cable can be supplied in bulk or as complete cable assemblies with connectors. Product is constructed with copper center conductor, aluminum tape bonded to polyethylene foam dielectric, tinned copper outer braid, and polyethylene outer jacket....

Electric Cable Assemblies

Cable Assemblies meet IEEE 802.11 standards.

MHF jumpers satisfy IEEE 802.11, Bluetooth(TM) and FCC Part 15 standards for wireless applications including WLAN, RF Test Points, and PDA devices. Jumpers use low profile connectors that occupy minimal board space while providing VSWR rating of 1.3 max. up to 6 GHz. TeflonÃ-® cables are used in RFW-10506-XX, MHF plug to MHF plug; RFW-10507-XX, MHF plug to pigtail; RFW-10508-XX, MHF plug to...

Electric Cable Assemblies

Coaxial Cable Assemblies suit low-outgassing applications.

Miniature versaFLEX and hyperFLEX cable assemblies include Models 3090DH and 3090DV, which offer 10-32 coaxial plugs on both ends. Models 3053H and 3053V have M3 coaxial plug on one end and 10-32 plug on the other. Built with materials that have Total Mass Loss of 1% or less and Collected Volatile Condensable Materials of 0.1% or less, versaFLEX cable assemblies utilize extruded-polymer jacket...

The Ultimate Guide to Enclosed Tubular Drag Cable and Disc Conveyors

This whitepaper provides a comprehensive overview of enclosed tubular drag cable and disc conveyors.

Electric Cable Assemblies

Jumper Cordsets conform to worldwide electrical standards.

Interpower(TM) cordsets supply power to system accessories and are offered in 0.5, 1.0, 1.5, 2.0, 2.5, and 3.0 m lengths. Products are molded with Harmonized cable and have UL recognition, CSA certification, and VDE approval. They are terminated on one end with IEC 60320 C13 connector and on other end with IEC 60320 Sheet E plug connector. Both terminations are molded directly onto cable....

Electric Cable Assemblies

Interconnect System suits telecommunications industry.

Ganged RF Interconnect System provides connections for 2.5 GHz bandwidth single-ended or analog RF signals in blind-mate daughtercard receptacles and backplane headers. Connectors offer 50 Ohm Ã-

Electric Cable Assemblies

Cable Assemblies/Sockets meet IDB/IEEE 1394 standards.

IDB IEEE1394 Consumer Convenience Port Connectors are offered in lengths up to 10 m and in 4 different versions: bilingual plug to bilingual plug, bilingual plug to beta plug, bilingual plug to IEEE 1394 AV plug, and bilingual to IEEE 1394-95 plug. Hot-pluggable units have positive locking feature and audible click. Copper-based system supports transmission speeds up to 1,600 Mbits/sec. Right...

Electric Cable Assemblies

Italian Cordsets are offered in custom lengths.

Interpower(TM) Italian cordsets are configured with 16 A molded Italian plug and are terminated with 3 different angled IEC 60320 C19 connectors. Units are IMQ approved at 16 A/250 Vac and are available with 3 x 1.50 mmÃ-² cable.

Electric Cable Assemblies

Cabling Equipment suits wire raised floor installations.

Products for pedestal cabling applications include CADDY CableCat(TM) J-Hooks with 3/4, 1 5/16, 2, and 4 in. dia loops and retainers; CableCat 425 wide-base cable supports that hold up to 425 four-pair cables; and CableCat pulley for cable pulling. Signal Reference Grid Clip provides quick attachment for grounding systems.

Electric Cable Assemblies

RF Attenuation Cable works in high voltage applications.

Quiet Line continuously extruded low pass filter provides RF power attenuation. It can be spliced onto existing high voltage lead, or supplied as assembly with or without silicone rubber coating. Its continuous thin wall coating is applied over FEP or PFA jacket. Coating allows user to achieve dielectric bond when potting or encapsulating with compatible silicone material. Cable is offered...