DC to DC Power Supplies (Converters)

DC/DC Converters provide 25-30 W output power.
DC to DC Power Supplies (Converters)

DC/DC Converters provide 25-30 W output power.

Offered in 27 models, Series ASD30 accepts 2:1 wide range inputs from 9-72 Vdc and provides single, dual, and triple outputs from 3.3-15 Vdc. All contain continuous short circuit protection, external O/P trim adjustment, and on/off control function. Internal input filter eliminates need for addition of external components. Encapsulated in copper case with non-conductive base, units provide 500...

Read More »
Dual Phase Boost Converter delivers 2 A in 3 x 3 mm DFN.
DC to DC Power Supplies (Converters)

Dual Phase Boost Converter delivers 2 A in 3 x 3 mm DFN.

Able to supply 2 A @ 5 V from 3.3 V input, LTC3428 current mode boost converter has input voltage range of 1.6-4.5 V. External parts count and size are minimized by 1 MHz per phase switching frequency and 2-phase design. External compensation allows feedback loop response to be optimized for particular applications. With efficiency rating to 92%, product features two 93 milliohm, 2 A N-channel...

Read More »
Boost DC-DC Converter IC drives white LEDs in series.
DC to DC Power Supplies (Converters)

Boost DC-DC Converter IC drives white LEDs in series.

Non-inverting Model A8430 provides programmable constant current output at up to 36 V, which is set with external resistor, and can be varied with PWM signal or control voltage at top of sense resistor when dimming control is required. With input voltage of 2.5-10 V, unit drives up to 5 LEDs at 20 mA from 3.0 V supply. Switching frequency of 1.2 MHz allows use of small external components. Model...

Read More »
Point-of-Load DC/DC Converter is remotely configurable.
DC to DC Power Supplies (Converters)

Point-of-Load DC/DC Converter is remotely configurable.

Non-isolated SIL15E-12M POL converter provides control flexibility for PCB design qualification and production testing. It combines conversion technology with voltage control features and incorporates IÂ-²C bus interface with open architecture. Product also provides active DC output control function and generates up to 15 A with full load efficiency of 92%. Converter has input voltage range...

Read More »
DC/DC Converters offer power density of 106 W/in.-³.
DC to DC Power Supplies (Converters)

DC/DC Converters offer power density of 106 W/in.-³.

Typhoon(TM) series of panel mount eighth- and quarter-brick converters includes two 20 A eighth bricks and two 30 A quarter bricks offering single isolated outputs of 1.8 and 3.3 V. Products employ full wave coupled-inductor topology in conjunction with processor-controlled synchronous rectifier circuit. Their 24 V input accommodates voltages in 18-36 V range, and above-board profile is 0.3 in.

Read More »
DC/DC Converter operates from 30-120 Vdc.
DC to DC Power Supplies (Converters)

DC/DC Converter operates from 30-120 Vdc.

Model MPD-810H-V can generate 85 W under conventional cooling and 120 W with 18 cfm forced air. It is fully protected against output overload and short circuits, and automatically recovers upon overload condition. MTBF value is greater than 135,000 hr. Suited for both railroad and telecommunication applications, unit utilizes thermally efficient U channel chassis and offers ATX output options.

Read More »
DC to DC Power Supplies (Converters)

DC/DC Buck Regulator operates at frequency of 900 kHz.

By integrating low resistance switches, 3 A PowerBlox(TM) SP7651 delivers efficiencies up to 92% over output voltage of 0.8-20 V. Featuring input voltage of 2.5-20 V, step-down regulator includes programmable soft start, over-temperature protection, dual under-voltage lock-out, and short circuit protection. It comes in 7 x 4 mm DFN package with 3 independent heat sinks and operating temperature...

Read More »
Step-Down DC/DC Converter has 100 -µA quiescent current.
DC to DC Power Supplies (Converters)

Step-Down DC/DC Converter has 100 -µA quiescent current.

Model LT1977, with constant 500 kHz switching frequency, features Burst ModeÂ-® operation. It utilizes 60 V, 1.5 A, 0.2 ohm switch with associated control and logic circuitry integrated into single die. Converter operates within VIN range of 3.3-60 V, making it compatible with load dump or cold-crank conditions in automotive applications. Features include power-good flag with programmable...

Read More »
Surface-Mount DC/DC Converter is offered in 75 W model.
DC to DC Power Supplies (Converters)

Surface-Mount DC/DC Converter is offered in 75 W model.

With input voltage range of 10-14 Vdc, APC18 point-of-load converters provide up to 18 A of regulated power with efficiencies to 92%. Non-isolated converters measure 1.3 x 0.53 x 0.35 in. and suit environments with restrictive space requirements. With adjustable external resistor programming, single-output devices can provide selected output voltage from 0.75-5.5 Vdc with regulation to within 3%....

Read More »
DC/DC Converters support up to 930 A/-µs load transients.
DC to DC Power Supplies (Converters)

DC/DC Converters support up to 930 A/-µs load transients.

Non-isolated, point-of-load, Series VRM10 meets core power requirements of high-end processors. Converters offer dynamic voltage programming and continuous current outputs up to 85 A. They use 4-phase buck conversion topology with interleaving to achieve switching frequency of 2.2 MHz, yielding conversion efficiencies up to 86% when delivering 85 A at 1.4 V. Complying with Intel's VRM10.0 and...

Read More »
Dies & Stamping Services with Over 25 Years of Experience
Sponsored

Dies & Stamping Services with Over 25 Years of Experience

PDS is an established leader in progressive die stamping, with a reputation for providing precision and value that dates back more than half a century. Through extensive capabilities and a staff of seasoned professionals, we set the standard for quality, delivering flexible services that can meet the needs of the most challenging requirements. See our video to learn more.

Read More »

All Topics