DC to DC Power Supplies (Converters)

DC/DC Converter takes up small amount of DIN-rail space.
DC to DC Power Supplies (Converters)

DC/DC Converter takes up small amount of DIN-rail space.

CP-DCDC 50 W family is available with 12 or 24 Vdc inputs, and has outputs including 5 Vdc @8 A, 12 Vdc @3 A, and 24 Vdc @2 A, with continuous short-circuit protection on output, and over and under voltage protection. Status indication is standard. Slim unit occupies only 2 1/4 in. of DIN-rail space. Module, with metal housing, mounts on TS 35 DIN rail. Optional chassis-mount hardware is...

Read More »
DC/DC Converters suit low voltage applications.
DC to DC Power Supplies (Converters)

DC/DC Converters suit low voltage applications.

PowerQor(TM) Tera Series half-brick isolated DC/DC converters include output voltages of 15, 12, 5, 3.3, 2.5, 2.0, 1.8, 1.5 and 1.2 V. All units draw power from 48 V nominal input and deliver 60 amps or 165 watts output. Typical efficiency for 1.2 V module is 88% at half-load (30 A) and 84% at full load (60 A). It provides full 60 A of output current at up to 70 deg C, and 200 LFM airflow with no...

Read More »
DC-DC Converter generates regulated output.
DC to DC Power Supplies (Converters)

DC-DC Converter generates regulated output.

Switched-capacitor ZXCP330E6 provides 3.3V output from 2 to 4.4 V input with maximum load current of 40 mA. Short-circuit and thermal-overload protected, SOT23-6 packaged converter suits lithium-ion and alkaline battery-powered products. Operating with flying capacitor of 220nF and 10 microF bypass capacitors at input and output, typical PCB area requirement is 8 x 5.3 mm. It draws 20 microA...

Read More »
DC-DC Converters do not require heat sink.
DC to DC Power Supplies (Converters)

DC-DC Converters do not require heat sink.

Dual output, NKA03 3.3V subminiature DC-DC converters allow any distribution of load across outputs as long as total does not exceed 1W. Galvanic isolation of 3kVDC between input and outputs ensures minimum switching noise. Typical line regulation is rated at 1%, while typical ripple and noise current ratings are 30mA (peak-to-peak). Converters are supplied in fully encapsulated, UL 94V-0...

Read More »
DC to DC Power Supplies (Converters)

DC/DC Converters suit board-level applications.

CostCutter converters are available in SIP/DIP and modular packages, providing output power over range of 0.75 to 60 watts. Units accept single-range and 2:1 range inputs from 4.5 to 72 Vdc, which provide single and dual outputs from 3.3 to 15 Vdc. All models contain short circuit protection and internal input filter. CostCutter Series will operate over ambient temperature range of -25 to...

Read More »
DC/DC converter needs no heat sink.
DC to DC Power Supplies (Converters)

DC/DC converter needs no heat sink.

Quarter-brick sized DualQor(TM) is capable of delivering up to 40 W of total output power at 3.3V and 2.5V. It employs synchronous rectification to achieve efficiencies up to 87%. Converter has 48V nominal input and meets input voltage transient requirements up to 100V for l00 msec. Unit has industry-standard footprint of 1.45 x 2.3 in. with profile of 0.43 in., and industry recognized pin out...

Read More »
DC/DC Converters feature isolated output.
DC to DC Power Supplies (Converters)

DC/DC Converters feature isolated output.

5E Series offers input voltage ranges of 9-18, 18-36, and 36-72 Vdc. Units are available with single, dual, and triple low rippled regulated outputs. CMOS/TTL compatible remote On/Off control allows converter output to be turned on or off as necessary. 25/30 watt converters feature continuous short circuit protection and do not require heat sink. They have 6-sided shielding and can achieve...

Read More »
DC/DC Converters accept wide range of dc inputs.
DC to DC Power Supplies (Converters)

DC/DC Converters accept wide range of dc inputs.

WD Series 10W dual output dc/dc converters have 4:1 dc input range to accommodate 12 V battery, 24Vdc industrial, and 48V telecom power sources. 3 models have input range from 9-36 Vdc, and 3 models have 18-72 Vdc input range. Outputs are ±5, ±12 and ±15 Vdc. All models are fully isolated input to output, have 5-sided shielded case, and offer optional on/off function to conserve...

Read More »
Frequency Converter transforms single phase to three phase.
DC to DC Power Supplies (Converters)

Frequency Converter transforms single phase to three phase.

Compact BL3X350 delivers 350 VA per phase of clean, regulated 3-phase ac power from single phase input. Digitally controlled waveform produces clean power while protection circuitry provides for voltage fold back during overloads to maintain undistorted waveforms. Switch selectable, single phase input accepts 115 or 230 Vac at 47-440Hz, so it can accept any worldwide, shipboard or aircraft single...

Read More »
DC/DC Converter works in low power applications.
DC to DC Power Supplies (Converters)

DC/DC Converter works in low power applications.

QML series isolated dc/dc converter can deliver up to 15 A total output current at 3.3V and below and up to 75W at 5V and above without need for attached heatsink. It uses synchronous rectification, resulting in no derating of output power up to 70 degrees C. Converter employs industry standard quarter-brick footprint and pin out, measures 1.45 x 2.3 in., and has low profile of 8.5mm. Functions...

Read More »

All Topics