DC to DC Power Supplies (Converters)

DC/DC Controllers provide output voltages down to 0.8 V.
DC to DC Power Supplies (Converters)

DC/DC Controllers provide output voltages down to 0.8 V.

Models MIC2198/9, offering current capability of 20 A, can power CPUs, DSPs, and FPGAs with up to 95% efficiency. Input voltage range is 4.5-32 V, making them suitable for 5, 12, and 24 V power bus systems. Model MIC2198 operates at 500 kHz, while Model MIC2199 operates at 300 kHz. Both units are housed in 4 x 4 mm MLFTM 12-lead package, and provide PWM current mode control, cycle-by-cycle...

Read More »
DC/DC Converters provide isolated output.
DC to DC Power Supplies (Converters)

DC/DC Converters provide isolated output.

Series 5E 25/30 W DC/DC converters feature pi-input filter and 2:1 input voltage ranges of 9-18, 18-36, and 36-72 Vdc. Regulated, low ripple, single, dual, and triple outputs are available. CMOS/TTL-compatible, remote on/off control allows output to be put into powered down, stand-by mode. Single-output converters have external Output Trim that allows output voltage to be set within ±10%...

Read More »
DC-DC Converters offer current sharing/parallel operation.
DC to DC Power Supplies (Converters)

DC-DC Converters offer current sharing/parallel operation.

Series T1UDC single output, 600 W converters feature output voltages of 3.3, 5, 12, 24, and 48 V. Inputs range from 22-32 Vdc or 42-56 Vdc. Units include remote turn-on/turn-off, ±5% voltage adjust range, and DC-operated ball bearing fan. Operating temperature range is -10 to +65°C. Over-voltage, over-load, and over-temperature protection is provided. Ruggedized units are available...

Read More »
POL Converter delivers up to 80 A at 0.9-1.8 Vdc.
DC to DC Power Supplies (Converters)

POL Converter delivers up to 80 A at 0.9-1.8 Vdc.

VÂ-·I Chip Voltage Transformation Module, Model V048K015T80 achieves response time of less than 1 µs and delivers up to 80 A while converting 48 V to 1.5 V. It has 1 MHz bandwidth and can provide bi-directional power flow with load. Depending on output regulation needs of application, unit can be operated open- or closed-loop. It meets demands of DSP, FPGA, ASIC, processor cores, and...

Read More »
DC/DC Converter delivers 250 mA/channel without inductors.
DC to DC Power Supplies (Converters)

DC/DC Converter delivers 250 mA/channel without inductors.

Model LTC3252 spread spectrum, step-down DC/DC converter can deliver 250 mA continuous output to 2 separate channels. It operates from 2.7-5.5 V, making it suitable for single cell Li-Ion or multi-cell NiMH/Alkaline applications. Both outputs are resistor programmable from 0.9-1.6 V. Switched capacitor fractional conversion enables it to attain efficiencies as high as 88%. Switching frequency...

Read More »
POL DC/DC Converters deliver 28 Amps.
DC to DC Power Supplies (Converters)

POL DC/DC Converters deliver 28 Amps.

Series LEN non-isolated, point-of-load DC/DC converters accept 12 V ±15% input and convert it to lower voltage from 0.8-3.3 V at 28 A or 5 V at 25 A. Two-phase, fixed-frequency, buck-regulator design enables them to simultaneously deliver 85-96% efficiency, 100 Â-µsec step response, and operating temperature to +70°C without derating. E-brick package is offered in both standard...

Read More »
DC to DC Power Supplies (Converters)

DC/DC Converters offer up to 94% efficiency.

E-class non-isolated, point-of-load converters feature power density of 247 W/inÂ-³. They are offered with 5, 10, or 15 A outputs and have no minimum load requirement. Used with 12 V nominal on-board bus source, units will operate from input voltage of 10-14 V. Open-frame, single-board converters employ synchronous buck topology, using fixed-frequency 300 kHz switching and ultra low...

Read More »
DC/DC Converters offer efficiencies to 91%.
DC to DC Power Supplies (Converters)

DC/DC Converters offer efficiencies to 91%.

Series ULQ single-output, quarter-brick DC/DC power converters are fully rated for 15, 20, and 25 A output currents and are aimed at 8-15 A applications. They deliver full rated output power/current at 70°C with 200 lfm air flow. Output voltages are 1.2, 1.5, 1.8, 2, 2.5, and 3.3 V. Input voltages are either 24 V or 48 V nom. All models offer 2250 Vdc isolation and line/load regulation of...

Read More »
Converters boast power saving efficiency.
DC to DC Power Supplies (Converters)

Converters boast power saving efficiency.

LTC3734 and LTC3735 DC/DC converters have 550 kHz operating frequency and power Intel's Centrino® mobile technology for thin and light notebook PCs. Converters are synchronous step-down DC/DC controllers with integrated MOSFET drivers and Intel® Pentium® M compatible power saving mode. Single-phase and PolyPhase® units provide up to 20 and 40 A load current respectively,...

Read More »
DC/DC Converters meet needs of processor-equipped loads.
DC to DC Power Supplies (Converters)

DC/DC Converters meet needs of processor-equipped loads.

Typhoon(TM) isolated Â-¼-brick converters include 1.2 V Model LQS100A48-1V2, offering full load efficiency of 84.5%, and 1.8 V Model LQS80A48-1V8 providing 89.7% efficiency at full load. Units operate from 48 V input over full 36-75 Vdc input voltage range, and offer adjustable output voltage from 110% down to 80% of nominal value. They include short circuit, over-voltage, and thermal...

Read More »
Cut and Bevel Pipe up to 63" Diameter with a Single Lightweight, Portable Machine
Sponsored

Cut and Bevel Pipe up to 63" Diameter with a Single Lightweight, Portable Machine

CS Unitec is a leader in power tools designed for industrial applications, with products that set the standard for robust performance and industry-leading reliability. Adding to our long list of innovation is a new line of pipe cutting machines. For cutting and beveling pipe up to 2" in thickness and diameters from 12" to 63", no other cutting system comes close. See our video to learn more.

Read More »

All Topics

COVID-19 Response Suppliers COVID-19 Response:
Can Your Company Help Provide Critical Supplies?

We are using the power of our platform to aid in the mass shortage of critical supplies. If your company can help provide supplies, capabilities, or materials for products such as N-95 Masks and Tyvek SuitsPlease let us know.

COVID-19 Response Suppliers