Custom Manufacturing Services

Additive Manufacturing Systems

Applied Rapid Technologies to Distribute Bolson Materials

Spools of ABS and ABS+ materials for production grade 3D printers FREDERICKSBURG, VAÂ- – Applied Rapid Technologies Corporation (ART), a leading provider of rapid prototyping and short-run production solutions announces the addition of Bolson Materials to our additive manufacturing materials offerings. These materials help lower operating costs and add value and features beyond those...

Read More »
Goodhart Sons Inc. Completes Spray Dryer Expansion Project
Steel

Goodhart Sons Inc. Completes Spray Dryer Expansion Project

Goodhart Sons, Inc., a steel fabricator and installer in Lancaster, PA was contracted by an equipment supply company to perform the fabrication, freight and installation of a structural steel tower for a 40 foot diameter spray dryer and auxiliary equipment. The project consisted of the fabrication and installation of approximately 410,000 lbs. of steelwork. While they are no stranger to working...

Read More »
Fine-Boring System achieves closed-loop operation.
Machine Bars

Fine-Boring System achieves closed-loop operation.

Allowing users to dial in tolerances while tool is mounted in machine tool, Romicron® systems produce high-accuracy holes at high RPMs. Users can produce finish bores with tolerances ofÂ- few microns in diameter and bore-to-bore variations of few tenths of one micron. Using cartridges or boring bars, every tool can be adjusted in diameter via dial ring in 2...

Read More »
Grinders

M&S Centerless Grinding Manufacturers Solar Energy Components

The tolerances for diameter size and roundness on the ID of a special tube made manufacturing costly and vendors difficult to find. Product acceptance was going through the roof, but the lack of an adequate supply of this key component caused delivery delays and increasing order backlog which jeopardized the entire project. Material: 304 SST tubing Critical Dimensions: OD – approximately .2500...

Read More »
Rubber

Bluestar Silicones Presents Elastomer Solutions at Medical Design and Manufacturing (MD&M) East Show

PHILADELPHIA – Bluestar Silicones will showcase its new Silbione® silicone elastomer solutions, including low durometer liquid silicone rubber (LSR) and self-bleeding LSR, at the upcoming Medical Design Manufacturing (MDM) East Conference (Booth #3744), June 18-20. Bluestar Silicones' new 1 Shore A (ShA) hardness product, Silbione LSR 4301, uniquely combines strong physical properties and...

Read More »
Valves

M&S Centerless Grinding Manufacturers Heart Valve Clip for Defective Heart Valves

The extremely small size of the part, critical to affixing a clip to a defective heart valve, resulted in manufacturing difficulties, and unacceptable inconsistencies in holding the required part tolerances. Critical Dimensions: Center Diameter size - .0191/.0190 OAL: .056 8 Ra surface finish .001" max inside corner radii Resolution: a manufacturing process was created that yielded 95% success...

Read More »
Grinding Services

M&S Centerless Grinding Manufacturers Missile Wing Pins for Tier 1 Defense Contractor

A Tier-1 defense contractor rejected parts from their primary vendor for a high-end precision pin used to affix fins onto missiles. The rejection of the pins caused a delay in shipment of missiles to The Persian Gulf, and left them with no source for the pins after the primary vendor lost approved status. The Tier-1 contractor needed to ship missiles within 2 weeks otherwise late delivery...

Read More »
Ipsen and ExOne Collaborate on Complete 3D Printing Solution
Additive Manufacturing Systems

Ipsen and ExOne Collaborate on Complete 3D Printing Solution

CHERRY VALLEY, IL – When constantly out-doing the competition is the name of the game, meaningful collaborations are of the utmost importance. Ipsen is pleased to have been selected by ExOne, a global provider of three-dimensional ("3D") printing machines and printed products, as a vacuum furnace provider as a part of an initiative to streamline production in the field of Additive Manufacturing...

Read More »
Controls and Controllers

Care for the Next Generation: ZW3D Supports and Creates Opportunity for Education

Guangzhou, ChinaÂ- – ZWSOFT, a leading supplier of 2D and 3D CAD/CAM solutions for the AEC and MCAD industries, is demonstrating their caring for education aiming at improving the learning environments. ZW3D, their cost-effective CAD/CAM solution, has been applied in many high schools, universities and educational institutions, helping the next generation become capable of and interested...

Read More »
Research, Design and Development Services

Biomedical Structures to Showcase Medical Textile Technology and Drug Delivery Platform with TissueGen at MD&M East

WHO:Â- Ã‚ Â Â Â Â Â Â Â Â Â Â  Biomedical Structures LLC (BMS), provider of biomedical textiles for medical devices and other clinical applications, will exhibit its medical textile engineering capabilities using absorbable and non-absorbable fibers for orthopedics, cardiology, general surgery, and tissue engineering...

Read More »
Precision Machining Solutions with Over 25 Years of Experience
Sponsored

Precision Machining Solutions with Over 25 Years of Experience

Quality, customer service, and unbeatable value are the hallmarks of Hogge Precision. Since 1989 we have built a reputation as the go-to precision machining source, servicing many demanding industries. For CNC machining and screw machining, there are few manufacturers that can match our capabilities and expertise. See our video to learn more.

Read More »

All Topics