New Converters Products

Digital Converter Modules provide DC velocity outputs.

Synchro-to-Digital Converters provide DC voltage output proportional to velocity, in addition to 10, 12, or 14-bit digital output. Velocity output of Ã-

Linear SAR ADC is suited for automated test equipment.

Manufactured in 6 x 6 mm QFN-28 package, ADS8372 successive-approximation (SAR) ADC features 16-bit no missing code performance and 600 kSPS data rate. It ensures integral nonlinearity less than 0.75 LSB and differential nonlinearity less than 0.5 LSB. Along with fully differential, pseudo-bipolar input range, unit offers 16-bit capacitor-based architecture with inherent sample and hold, 4.096 V...

Concentrator System converts HART signals to MODBUS RTU.

HCS HART Concentrator System converts HART digital signal to RS-485 MODBUS RTU communication protocol, permitting up to 16 smart HART-capable transmitters and valves to interface directly with MODBUS-based monitoring and control systems. Users can monitor primary and non-primary process variables from various devices, and MODBUS system can monitor HART instrument diagnostics using Field Device...

Electronic Interface works with turbine flow meters.

PC-programmable F5140 K-Factor Scaler acts as field-adjustable frequency divider, converting pulsed frequency output from turbine flow meter to scaled, square wave output. It provides interface for PLC, RTU, PC DAQ cards, or any frequency counter or data input device. With optional software, unit also converts turbine meter output into frequency for other units of measurement. Interface includes...

The Ultimate Guide to Steam and Water Ejectors

Take A Comprehensive Look at Steam and Water Ejectors.

Differential Amplifier uses single power supply.

Model LT1994 draws 14 mA supply current while achieving -94 dBc harmonic distortion at 1 mHz and 3nV/√Hz voltage noise. Unit drives 2.5 and 3 V SAR ADCs without negative supply. Shutdown pin reduces consumption to 300 Ã-µA and amplifier is capable of sourcing and sinking to 85 mA. Specified for operation from 2.375-12.6 V, LT1994 is suited for industrial, instrumentation, and medical...

Converters enable low-noise transport of logic signals.

Electrical-to-Optical Converter, Model J720 and Optical-to-Electrical Converter, Model J730 convert logic levels to fiberoptic media for low-noise transport up to kilometers, with link jitter below 10 ps rms. Model J720 is powered by logic-level input, and Model J730 requires +12 V supply, user-furnished or from wall-plug power adapter. Model J730 provides digital logic output with risetime below...

SCR Converters withstand severe conditions.

SixPac(TM) includes 3 dual isolated SCR modules that can be configured as 3-phase ac controller or regulated dc converter. Measuring 18 x 10 x 11 in., modules are mounted on heatsink and are equipped with input fuses, Hall effect current sensor, output bus, cooling fan, and capacitor filter bank. Units feature input voltages of 10-700 Vac and output currents from 50-1,000 Adc or 100-600 Aac rms...

POL Converters are suited for densely populated boards.

Occupying board area of 2.14 in.Ã-², open-frame PTHxx040W series features output voltage adjustment and Auto-Track(TM) power sequencing. Model PTH12040W has output current rating of 50 A and 8-14 V input voltage range, while PTH04040W has 60 A rating and input range of 2.95-5.5 V. Series is Point-of-Load Alliance (POLA)-compliant and employs switching frequency of 1.05 MHz to achieve full...

Intermediate Bus Converters output up to 450 W power.

Typhoon(TM) quarter-brick IBC series includes IBC38AQT unregulated, fixed ratio dc transformer for computing, which features 337 W/in.Ã-³ power density and over 95% efficiency. Series also includes 2 semi-regulated models with input voltage ranges optimized for telecom (IBC28AQW) and networking (IBC30AQS) applications. All models have isolated 12 V outputs and use full bridge conversion...

Wideband ADC consumes 395 mW of power.

Housed in 32-pin, 5 x 5 mm QFN package with integrated bypass capacitors, 14-bit LTC2255 Analog-to-Digital Converter provides 125 Msps sampling rate and ac performance of 72.1 dB SNR/85 dB SFDR at 70 MHz input. Operating from 3 V supply, it is available in commercial and industrial temperature grades. ADC is suited for battery powered, high performance, test and instrumentation equipment such as...

Precision Machining Solutions with Over 25 Years of Experience

Quality, customer service, and unbeatable value are the hallmarks of Hogge Precision. Since 1989 we have built a reputation as the go-to precision machining source, servicing many demanding industries. For CNC machining and screw machining, there are few manufacturers that can match our capabilities and expertise. See our video to learn more.