New Controls & Controllers Products

Dual-Stage System produces reusable water from wastewater.

Membrane Bio Reactor combines diffused aeration and biological treatment with membrane filtration to produce reusable water in 8 hr. After air is added to incoming effluent, bacteria reduce organic content. Stage 2 filters water through membranes resembling rows of straws with microscopic pores that draw clear liquid into them while keeping solids out. System can be operated automatically from...

Motion Controller links up to 16 servo amplifiers.

Offered in 1-, 2-, 4-, and 16-axis versions, Digital MMC mounts directly in one 230 or 460 V MMC Smart Drive servo amplifier and controls it and up to 15 additional units daisy-chained together via RJ-45 connection. Field-installable product includes 8 dc inputs and 8 dc outputs on-board; I/O on each drive is accessible to application program over digital network. Unit also provides an...

Wireless I/O System utilizes FHSS technology.

Multipoint-to-point Model RAD-ISM-900-BD-BUS brings multiple channels of I/O from up to 8 remote locations back to one master station. Bi-directional feature enables use of device in monitoring and control applications and eliminates cable and conduit for analog and digital signals in harsh industrial environments. Typical in-plant range is 600-1,000 ft with no line of sight. Transceivers and I/O...

DC Motor Speed Control has current loop input signal option.

Rated to 2.0 hp, variable speed 250 Series is available with -5 or -7 option board that enables it to accept 4-20 mA current loop reference signal as command for speed control. Its -7 option also offers Auto/Off/Manual selection capability. DC drive is fully rated, with no auxiliary heat sink required, and is available in open chassis version or NEMA 4/12, 4X enclosed cULus Listed package.

An Operations Manager's Guide To The Mobile Connected Factory of Tomorrow

This white paper provides an overview of mobile technology for managing your manufacturing facility, while also discussing the advantages of being an early adopter.

Dispensing Valve Controller helps eliminate dripping.

Model VC-1195A can control both ON and OFF action of 1 or 2 dispensing valves. By using air to open and close valve, unit maximizes valve suck-back action and minimizes material stringing problems.

Process Control System has open, secure architecture.

Experion(TM) Process Knowledge System R300 includes Series C optionally redundant process I/O family with vertical design. Embedded cyber security technology prevents denial of service attacks and message flooding at control level. Product also incorporates automated backup and restore product as well as integrated solution that automates complex procedures. By capturing and implementing best...

RTU/Controller Interface enables real-time plant floor DAQ.

With built-in mix of 14 discrete and analog I/O, 4 serial ports, and 10/100 Ethernet interface, Micro-VersaTRAK Ã-µIPm provides flexible platform for plant floor interfacing. It comes pre-loaded with open-source Linux and industrial IPm firmware, which provides automation, control, and data acquisition (DAQ) capabilities as well as flexibility to program Linux or IEC 61131 applications....

Multipurpose AC Drive features zero-stacking design.

Variable-speed Model GV6000 comes in 7 frame sizes ranging from 0.5-200 hp at 480 V. Removable Operator Interface Module provides metering, programming, and operator control, and contains CopyCat functionality for transferring parameter sets between drives. Model GV6000 incorporates general-purpose control, sensorless vector control, and flux vector control with or without encoder feedback....

I/O Board provides secure front panel connections.

Model AVME9668 non-intelligent slave board interfaces IP modules to VMEbus. The 6U board holds 4 IP modules. Field I/O connections are made through front panel of carrier board. To accommodate rugged, high-performance applications, front-panel SCSI-2 connectors provide screw-down or spring latch connections that hold cables securely. With support for 8 and 32 MHz clocks, data can be processed at...

Motor Controller drives unipolar stepper motors.

Easy-Step(TM) 3000 motor drive and control system drives unipolar stepper motors in full 2-phase, full 1-phase, and half-step modes up to 35 V and 3 A/phase. Direct command set, slave/remote pulse mode, voltage mode, and teach mode operations are all supported. Measuring 63.6 x 26.4 mm, drive also features store and replay; selectable pull-in rate and maximum step rate; and adjustable ramp time...

How SpinSelect Can Save You Time and Money

Thanks to the unique SpinSelect™ Multi-Pocket selectable quick change tool holder, it's time to rethink the range, complexity and volume of parts that your lathe can produce. Our Spin-Select™ tool was created to increase productivity and consistency by decreasing downtime associated with lathe cutting tool and insert setups or changeovers. This product is a game-changer for the industry and we're pleased to show you why.