New Controls & Controllers Products

Data Acquisition Devices delivers input at rates to 800 kS/sec.

NI PXI-6120 and NI PCI-6120 simultaneous sampling, multifunction DAQ devices deliver 16-bit analog input on each of 4 channels for transient measurements and frequency domain measurements. Users can synchronize onboard digital I/O and waveform output with devices' waveform acquisition for mixed signal and stimulus-response applications. Products come with 64 million samples of onboard memory, two...

Microcontrollers maintain water temperature.

Microcontrollers, for use in instant hot water heaters for home, hotel, or industrial use, can be wired to circuit card in space-saving, wall-mounted heating unit programmed to maintain temperature within Ã-

Lift Gate Power Unit offers smart technology.

MaintenanceMinderÃ-²(TM) helps fleets measure and record lift gate performance and operating data while protecting gate from damaging conditions. It stores number of low voltage cycles, high temperature operations, number of lifts/cycles and total run time on motor. Unit can be programmed to alert user when scheduled maintenance is due and record when work is performed. Backlit display...

Operator Interface displays measurements simultaneously.

Able to display level, interface, and temperature measurements, stand-alone Model CL01 has LCD readout screen and expanded keypad functionality to provide at-a-glance measurements from MTS DDA or Modbus RTU interface. Diagnostic screen monitors trigger levels, and error flags aid engineers in troubleshooting problems. Offerings include 2-line x 20-character display with LED backlight, selectable...

7 Steps to Optimize Your Spring Design for Your Next Project

This white paper provides an in-depth overview into how to optimize a compression spring design in seven steps.

Router/Controller supports wireless transceivers.

Pathfinder Lx(TM) wireless inter-networking controller builds remote industrial and utility SCADA Ethernet and TCP/IP based wide-area wireless networks. Integrated SCADA device gateway supports all network ready Ethernet RTU/PLC or I/O devices. Built-in networking engine supports building of peer-to-peer, point-to-point, multi-point, and mesh topologies including wireless relays and hubs. Unit...

PCD Interface Modules provide in-line fusing capability.

In-line fusing module provides fusing and blown fuse indication for every circuit in distributed I/O systems. Consisting of board-mounted fuse and indicator elements housed in mounting system, module secures to DIN track. It connects to system I/O connector through board-mounted terminal blocks on interface module through multi-pin electronic connector (D-sub, ribbon cable, RJ style, Centronic,...

Motion Processor features parallel interface.

Parallel Pilot(TM) single-axis motion processor chip provides brushed, brushless, pulse and direction, and microstepping motion control. It communicates with host processor via bi-directional 16-bit parallel data port. Compared to typical serial interface of 416 kbaud, parallel port communication speeds are up to 6 times faster. Processor is suitable for embedded systems in industrial,...

Handheld Module instantly transmits data to Pocket PCs(TM).

Handheld Wireless Information Module(TM) (WIM) provides real-time, remote access to statistics and maintenance data by communicating directly with main system controller via Open Process Control (OPC) interface to Microsoft Visual Studio.NET(TM) WebService(TM). OPC support enables unit to integrate with any existing OPC-compliant applications and uses WiFi 802.11b for radio frequency...

Adjustable-Frequency Drives range from 1/2 to 5 hp.

VLTÃ-® MICRO Drives are offered in Ã-½-5 hp range for 230 Vac applications and 1-5 hp for 460 Vac applications. Digital keypad/display module is mounted to front panel. Units include programmable digital input and outputs, overload current to 150% of rated current for 1 minute, automatic voltage regulation, S-curve or linear ramp profiles, momentary power failure restart, and panel or...

Interface Module and Software synchronizes with DAQ.

Model FP-1300 FieldPoint CAN interface module provides access to 50+ I/O modules by adding distributed I/O to capabilities of CAN-based measurement systems and direct CAN connectivity to sensors/actuators. Users can add CAN nodes containing up to 9 I/O modules each to existing CAN networks. NI-CAN v2.0 driver software allows engineers to specify arbitration ID and customize I/O data configuration...