Proces Controller combines PLC, RTU and DCS architectures.
ControlWave LP utilizes 486-based CPU design for SCADA applications. It offers isolated I/O with wide temperature operation of -40 to +70 deg C for remote sites, and low power consumption for solar applications. Local I/O provides 16 DI, 8 DO, 8AI, 4HSC and up to 8 optional AO. ControlWave LP has 5 serial-communication ports and one 10 Mb Ethernet I/P port. Single controller provides logic,...Read More »
Controller handles low flows.
Micro-Flo combines characterized needle valve with internal differential pressure-regulating valve. By controlling pressure drop across adjustable orifice, flow rate remains constant. Response time to pressure variations is immediate. Applications include chromatographs, mechanical seals, chemical injection, blending systems, instrument purge systems, natural gas, nitrogen generation, and...Read More »
Low Dropout Regulator is available in S-Pak package.
MIC37150/1/2 1.5A LDO is designed for powering 1.5, 1.8, or 2.5 V from minimum supply of 2.25 or 3.0 V. It features dropout of 500mV over all conditions. MIC37150 is a 3-terminal device; MIC37151 includes error flag to warn of fault condition and enable pin for on/off control; and MIC37152 offers adjustable output voltage as well as on/off control of output voltage. uCap design allows use with...Read More »
Controller allows close safety light curtain mounting.
LCM Series Controller is designed for use with company's MC4700 and MS4700 light curtains. It includes removable terminal blocks and 2-digit numeric display. Two PNP solid-state safety outputs reduce response time. Three user-selectable operating modes include Automatic Start, Start/Restart Interlock and Start Interlock. Controller has 100 mm DIN enclosure and provides MPCE monitoring, remote...Read More »
A Guide to Robotic Cells in Automation: Electronics & Auto Parts
This white paper provides an overview into robotic cells in automation electronics and auto parts.Read More »
Ethernet Switches handle 8 or 9 channels.
Single-chip, 8-port KS8997 and 9-port KS8999 switch ICs can be used in 10/100 Ethernet DSL, cable, and wireless routers and gateway networks. Both support DiffServ and IEEE 802.lp to prioritize different classes of voice, video and data traffic. With port-based VLAN, devices allow user to establish VLAN groups for security between groups and applications. Devices handle up to 9 MACs, 8 PHYs,...Read More »
I/O Controller uses 20-pin Molex connector.
IOC-7007 I/O controller includes 10/100 Base-T Ethernet port and input and output options. It can accept up to 7 I/O IOM modules, available with TTL inputs, optoisolated inputs, optoisolated outputs, high power outputs, dry contact relays, analog inputs, or analog outputs. IOC-7007 incorporates 32-bit microcomputer with memory and multitasking. Box-level version accepts 90-260 VAC or 20-60 VDC,...Read More »
Controller/Driver controls 4 stepping motors at once.
Integrated MCB-4B board simultaneously controls up to 4 stepping motors with mini-step capability, and with 4, 6 or 8 leads and up to 3 amp phase current. Each axis is addressable, and several boards can be controlled by single computer communication port. MCB-4B offers stepping rates up to 50,000 step/sec and up to 16.7 million steps per move. It includes programmable acceleration/deceleration,...Read More »
Spanner Module offers visible rotary address switches.
FDN-DN1 Spanner module provides means to route data between 2 PLCs using DeviceNet(TM). By connecting DeviceNet networks directly, it eliminates needs for high-level control network pyramids. FDN-DN1 appears to each PLC as standard rack of I/O. Any DeviceNet scanner can send I/O data to Spanner module without additional software or complex configuration procedures. It is capable of transferring...Read More »
Contouring Control machines complex geometries.
With its digital motor control, iTNC 530 produces programmed contour on workpiece. Programs written at remote locations containing large amounts of data can be transmitted at high transfer rates over Fast Ethernet interface. Blocks can be inserted and modified in seconds. For machining complex geometries, control offers fixed cycles that simplify programming. Block processing time is 0.5 ms.Read More »
Servo Drive connects via CANopen interface.
DC201E25A20NAC digital servo drive uses CANopen communications for use in networking applications. Built-in interface complies with DS301 and DSP402 standards. Drive uses DSP to close digital current, velocity, and position loops for controlling brushed or brushless servomotors. Position and velocity loops can use encoder, Hall sensor, or analog feedback. Drive has output of 25A peak, 12.5A...Read More »
New Davenport Hybrid Machine Offers Unique Flexibility for Parts Manufacturing
The Davenport Hybrid machine offers greater flexibility, easier set-ups, and faster cycle times. Check out the video to learn more.Read More »