Ethernet Switches handle 8 or 9 channels.

Single-chip, 8-port KS8997 and 9-port KS8999 switch ICs can be used in 10/100 Ethernet DSL, cable, and wireless routers and gateway networks. Both support DiffServ and IEEE 802.lp to prioritize different classes of voice, video and data traffic. With port-based VLAN, devices allow user to establish VLAN groups for security between groups and applications. Devices handle up to 9 MACs, 8 PHYs,...

Read More »
I/O Controller uses 20-pin Molex connector.

I/O Controller uses 20-pin Molex connector.

IOC-7007 I/O controller includes 10/100 Base-T Ethernet port and input and output options. It can accept up to 7 I/O IOM modules, available with TTL inputs, optoisolated inputs, optoisolated outputs, high power outputs, dry contact relays, analog inputs, or analog outputs. IOC-7007 incorporates 32-bit microcomputer with memory and multitasking. Box-level version accepts 90-260 VAC or 20-60 VDC,...

Read More »
Controller/Driver controls 4 stepping motors at once.

Controller/Driver controls 4 stepping motors at once.

Integrated MCB-4B board simultaneously controls up to 4 stepping motors with mini-step capability, and with 4, 6 or 8 leads and up to 3 amp phase current. Each axis is addressable, and several boards can be controlled by single computer communication port. MCB-4B offers stepping rates up to 50,000 step/sec and up to 16.7 million steps per move. It includes programmable acceleration/deceleration,...

Read More »
Spanner Module offers visible rotary address switches.

Spanner Module offers visible rotary address switches.

FDN-DN1 Spanner module provides means to route data between 2 PLCs using DeviceNet(TM). By connecting DeviceNet networks directly, it eliminates needs for high-level control network pyramids. FDN-DN1 appears to each PLC as standard rack of I/O. Any DeviceNet scanner can send I/O data to Spanner module without additional software or complex configuration procedures. It is capable of transferring...

Read More »
Contouring Control machines complex geometries.

Contouring Control machines complex geometries.

With its digital motor control, iTNC 530 produces programmed contour on workpiece. Programs written at remote locations containing large amounts of data can be transmitted at high transfer rates over Fast Ethernet interface. Blocks can be inserted and modified in seconds. For machining complex geometries, control offers fixed cycles that simplify programming. Block processing time is 0.5 ms.

Read More »

Micro Controller offers distributed processing.

FEC-FC34, with 10Base-T connectivity and TCP/IP protocol, provides local and remote process communication. It operates on 24 Vdc and has 12 inputs (user configurable as PNP or NPN) and 8 outputs. Two inputs can be used as high speed counters. 16-bit 20 MHz processor allows for multi-tasking of up to 64 programs. When connected to network, process/control information is available for enterprise...

Read More »
Motor and Driver includes onboard electronics.

Motor and Driver includes onboard electronics.

MDrive34 uses NEMA 34 frame size 1.8° motor combined with microstepping drive, and accepts up to 14 resolution settings from 1/2 to 256 microsteps per step. Setup parameters include Microstep Resolution and Run-and-Hold currents, and can be changed on-the-fly or downloaded and stored in non-volatile memory with GUI. Operating voltage is +24 to +75 VDC. MDrive34 is available in single stack,...

Read More »

Servo Drive connects via CANopen interface.

DC201E25A20NAC digital servo drive uses CANopen communications for use in networking applications. Built-in interface complies with DS301 and DSP402 standards. Drive uses DSP to close digital current, velocity, and position loops for controlling brushed or brushless servomotors. Position and velocity loops can use encoder, Hall sensor, or analog feedback. Drive has output of 25A peak, 12.5A...

Read More »
Press Control requires no NC programming.

Press Control requires no NC programming.

Optifeed-C system controls roll feed, provides digital synchronization between start time and main drive of press, and maximizes number of strokes of press line. Predefined and selectable functions include automatic feed adaptation, start-point displacement, programmable switch cam group, and setpoint output for coil processing. Only inputs required are process specific inputs, including length,...

Read More »
Temperature Controller works in water systems.

Temperature Controller works in water systems.

Microprocessor based 1/16 DIN PID controller provides precise, stable, straight-line control in circulating water temperature control systems. It has autotuning, thermocouple and RTD inputs, programmable soft start, dual LED display of setpoint and liquid temperature, and menu-driven operation. Other applications include temperature control systems in plastics, chemical, packaging, and food...

Read More »
Krueger Sentry Gauge Announces the Release of Two New Chemical Sight Gauge Models Designed for Aggressive Liquid Storage Monitoring
Sponsored

Krueger Sentry Gauge Announces the Release of Two New Chemical Sight Gauge Models Designed for Aggressive Liquid Storage Monitoring

Krueger Sentry Gauge, a leader in chemical sight gauges, now offers the ultimate in aggressive liquid storage monitoring devices. From sulfuric and hydrochloric acid to bleach, and acetone, our products are designed with robust features that deliver a long and trouble-free service life. See our video to learn all about this new and innovative line of sight gauges.

Read More »

All Topics