Controls and Controllers

DCS Controller is built on Linux platform.

Modular SixTRAK IPm(TM) Open DCS Controller provides 5 Ethernet and 3 serial ports. It is scalable from 1 to 16,000+ stations with unlimited I/O expansion (50,000+). Internet-enabled unit features 2 unique IP addresses for redundant networking, 32-bit PowerPC, and open-source Linux software. SixTRAK IPm is suitable for process control, Supervisory Control and Data Acquisition (SCADA), and...

Read More »
Controls and Controllers

Thermocouple Input Module expands capabilities of controller.

Model 1762-IT4 allows users to directly connect MicroLogix(TM) 1200 controllers to any of 9 types of thermocouple temperature sensors or millivolt sensors. Four-channel module offers accuracy ranging from ±.5 to ±7.5°C, depending on thermocouple input type. It is factory-calibrated and can be programmed to perform auto calibration on cyclical or non-cyclical basis. Unit provides...

Read More »
Controls and Controllers

Process Control System provides DeviceNet(TM) connectivity.

ProcessLogix(TM) Release 500 allows users to connect existing ODVA-compliant plant floor devices into their system. It supports NetLinx(TM) open-network architecture, providing seamless routing from one network to another without additional programming. Server is OPC 1.0 Alarm and Event compliant, allowing OPC alarm and event clients to access data originating from ProcessLogix. System also...

Read More »
Laser Controller acquires all necessary analog signals.
Controls and Controllers

Laser Controller acquires all necessary analog signals.

LCON series Configurable System-on-a Chip (CSoC) laser controller acquires optical power, reflected power, temperature, and laser diode current signals. It can process and react to data in less than 5 Â-µs, resulting in 200 kHz response rate. With reconfigurable hardware and firmware, series has system memory capacity with 2 MB FLASH, 8 MB SDRAM, and 8 KB EPROM. Adaptive TEC temperature...

Read More »
Controls and Controllers

Electrical Control Station is used for training purposes.

Training and testing center is comprised of stand alone panel that contains functioning electrical schematic that permits user to change control circuitry to experiment with new configurations. Measuring 4 x 8 in., panel includes banana clip style connectors, stop/start circuits, on and off relay delays, control relays, selector switches, load cells, digital indicators, temperature probes, and...

Read More »
Linear Drive Assembly enables ramp down of linear speed.
Motor Controllers and Drives

Linear Drive Assembly enables ramp down of linear speed.

Option K enables mechanical control over ramp down speed prior to reversal of drive head. It features auto-reverse, zero backlash, variable pitch, up to 800 lbs axial thrust, and accuracy to within ± 0.005 in. Travel speed may be up to 13 ft/sec, at constant rpm, over max distance of 16 ft. K Option is suitable for converting, metalworking, and finishing operations where reversal of drive...

Read More »
Controls and Controllers

Temperature Control System suits semiconductor processing.

OMEGA® iR2(TM) temperature measurement and control system uses 2-color ratio technique for temperatures from 300 to 3,000°C, even when measuring small, moving target with changing emissivity viewed from outside window. It comes with compact lens and fiber optic cable. System features through-the-lens laser sighting for precise focus and alignment. It includes full PID control output,...

Read More »
AC Servo Drive/Motor suits small machine tool applications.
Motor Controllers and Drives

AC Servo Drive/Motor suits small machine tool applications.

ECODRIVE Cs series system-compatible AC servo drive is offered in 100-750 W power range with 230 Vac, 1- or 3-phase power input. Unit measures 2.17 x 7.17 x 6.69 in. (W x H x D). Motor includes options for built-in holding brake, keyed output shaft, and absolute feedback. Available with various open bus interfaces, ECODRIVE Cs incorporates firmware that embodies process-oriented technologies...

Read More »
Machine Control handles single- and multi-axis applications.
Controls and Controllers

Machine Control handles single- and multi-axis applications.

With modular system concept, open control structure, and internationally standardized interfaces, VisualMotion provides solutions for automation architectures. Intelligent drive system and servo drives allow product and process changes to be made electronically. Modular Windows-based control software synchronizes up to 32 servo axes, communicating via SERCOS, Ethernet TCP/IP, PROFIBUS-DP,...

Read More »
Linear Module is certified for Class 10 cleanroom use.
Positioners

Linear Module is certified for Class 10 cleanroom use.

Type PSK linear module, suitable for semiconductor and life science industries, uses sealing strip to prevent contamination in sensitive environments. Extruded steel base with integral ball rail guide way enables PSK Precision Modules to achieve positioning repeatability of 0.005 mm with payloads up to 44,760 N at speeds up to 1.6 m/sec. Interchangeable with other modules, PSK can be used to...

Read More »
Delivery Equipment That Really Delivers
Sponsored

Delivery Equipment That Really Delivers

Are you in need of safer, more efficient transportation equipment? Do you feel like your delivery equipment could really use an upgrade? Check out this video, and learn about Halo Ramp Company's patented safety platforms, and how they help you bypass your trickiest delivery challenges.

Read More »

All Topics

COVID-19 Response Suppliers COVID-19 Response:
Can Your Company Help Provide Critical Supplies?

We are using the power of our platform to aid in the mass shortage of critical supplies. If your company can help provide supplies, capabilities, or materials for products such as N-95 Masks and Tyvek SuitsPlease let us know.

COVID-19 Response Suppliers