Control System optimizes engine performance.
Controls and Controllers

Control System optimizes engine performance.

Engenius ESM Engine System Manager, directed by Engine Control Unit (ECU) monitors speed, pressure, temperature and other engine conditions; controlling ignition timing, speed governing and stop/start functions. It also provides diagnostic help and fault logging when requested. System can be packaged to instantly communicate to Internet server, computer, phone or pager via satellite, cellular...

Read More »
Ultrasonic Positioner measures travel of valve blade.
Valve Positioners

Ultrasonic Positioner measures travel of valve blade.

EP 2000 compares valve position to valve control signal, and provides valve open, valve closed, positioner start, positioner stop, and valve blade not in position indications. It works with 4 to 20 mA signal from DCS system, where at 4 mA signal valve is completely closed, at 20 mA completely open. Probe can also be trained to use 4 to 20 mA signal for partially opening and closing valve.

Read More »
Worm Gear Drives provide ratios from 1:1 to 60:1.
Motor Controllers and Drives

Worm Gear Drives provide ratios from 1:1 to 60:1.

DAW Series multi-speed transmissions will shift on-the-fly under full load. Model DAW is rated at up to 50 input HP at 1800 RPM and comes in 4 basic configurations. DAW-S is single input with single output shaft; DAW-SD is single input with dual output shafts that may be solid or split; DAW-DS is single input with dual output shafts and output shafts are coaxial shaft-over-shaft; DAW-SI is single...

Read More »
Intelligent Controllers feature modular designs.
Motor Controllers and Drives

Intelligent Controllers feature modular designs.

SMC-3(TM) 3-phase Smart Motor Controller includes standard overload protection with adjustable trip class, motor and system diagnostics, configurable auxiliary contacts, and multiple start and stop modes. SMC-Delta(TM) reduced voltage starter is designed for star-delta (6-lead motor) applications. It incorporates transitionless start, and combines contactors, overload relays, timers, and internal...

Read More »
Ethernet Module produces pneumatic pressures.
Interfaces

Ethernet Module produces pneumatic pressures.

Model ENETCPM control pressure module can supply pneumatic pressures or relay logic on demand, based on commands sent via Ethernet or Internet. It has eight digital circuits controlled by onboard microprocessor: three are for internal solenoid valves, and five circuits are available for lights, switches or valves. Communication is 10BaseT via TCP/IP protocol. Its embedded web server communicates...

Read More »
Switching Regulator handles double data rate memory.
Electrical Regulators

Switching Regulator handles double data rate memory.

Self-contained FAN6555 handles termination requirements of DDR memory arrays. It has high-efficiency MOSFETs capable of handling up to 2A (source and sink) of continuous load current and 3A peak current at termination voltage, regulated to 13% over changing load conditions. Regulator has buffered VREF output for cascaded bus systems, shutdown control for standby mode and thermal shutdown...

Read More »
Motion Control Chipsets synchronize multiple axes.
Controls and Controllers

Motion Control Chipsets synchronize multiple axes.

Navigator and Pilot chipsets control brushed dc servos, brushless dc servos, steppers, and microsteppers. Navigator handles 4 axes, while Pilot handles 1. Multi-chip synchronization allows more than 4 axes of motion to be coordinated between any combination of Navigator and Pilot chips. It also allows physically remote or distributed chips to be synchronized within microseconds so they can be...

Read More »
Mass Flow Controller also records and manipulates data.
Controls and Controllers

Mass Flow Controller also records and manipulates data.

Series DMF can be programmed for functions such as flow set point, totalizer, stop totalizer, totalize from preset flow, stop and preset auto, and auto zero. It has two outputs to operate pumps, valves or other equipment, and can control high and low alarm limits through its RS485 interface. Flow ranges vary from 0-10 sccm to 0-100 L/min with accuracy of ±1% of full scale. Operating...

Read More »
I/O Modules are for programmable controllers.
Modules

I/O Modules are for programmable controllers.

I/O modules work with CompactLogix and MicroLogix controllers. 1769-HSC 1-MHz counter/encoder input module has 4 on-board 5-30V dc sourcing outputs for high-speed applications such as flow, speed, frequency and duration control, and length measurement and positioning. 1769-IF4XOF2 combination analog I/O module has 4 input channels and 2 output channels, with 1 unipolar voltage and 1 unipolar...

Read More »
Drum Motor Drives drive food conveyors.
Motor Controllers and Drives

Drum Motor Drives drive food conveyors.

Internally powered drum motors are available with USDA Dairy 304 or 316 stainless steel shell, shafts and end flanges that resist corrosion and contamination prohibited in food industry. Each motor is filled with food grade oil and hermetically sealed, making it suitable for applications requiring daily high-pressure washdown and acid or alkaline power washings. Drives have sprockets for driving...

Read More »
Precision Machining Solutions with Over 25 Years of Experience
Sponsored

Precision Machining Solutions with Over 25 Years of Experience

Quality, customer service, and unbeatable value are the hallmarks of Hogge Precision. Since 1989 we have built a reputation as the go-to precision machining source, servicing many demanding industries. For CNC machining and screw machining, there are few manufacturers that can match our capabilities and expertise. See our video to learn more.

Read More »

All Topics