New Controls and Controllers Products

Feeder Control connects directly to plant PLC.

Integrating control and motor drive modules directly on feeder, K-Tron Control Module is available with integrated operator interface keypad display or as blind cover with status display. It can function as volumetric or gravimetric feeder controller, and supports all K-Tron feeders equipped with SFT II or SFT III load cells. Meeting IP 65/NEMA 4 standards, module is suited for hazardous areas...

Control System monitors all types of industrial plants.

Plant Control System provides voltage control, VAR control, breaker control, generator start/stop, synchronization, pump control, and multi-generator load control in one integrated system. Performing up to 73 MIPS, G4 Remote Terminal Unit features real-time OS, multiple interfaces, and protocol support. Software includes MC3000 SCADA Master in real-time Linux, dynamic port assignments,...

Step-Down Controller manages mobile PC power.

Dual Step-Down Model PM6685 provides 4 output voltages necessary for notebook system power, with conversion efficiency up to 96% using loss-less current-sensing technique. Two PWM voltage regulators provide fixed 5 and 3.3 v outputs that power system during normal operation, while 2 LDO linear regulators provide 5 and 3.3 V output for system standby. Selectable switching frequency allows 200/300,...

Microcontrollers target battery-powered applications.

Utilizing very low-power oscillator technology, Series MSP430F20xx delivers 500 nanoamp standby mode and is totally self-clocked with self-wakeup capability using no external components. Digitally controlled oscillator is programmable up to 16 MHz with ability to switch from standby to full operation in less than 1 Ã-µs. Operating from 1.8-3.6 V, microcontrollers enable fire detectors and...

Avoid Pressure Equipment Failure

This eBook gives a guide on how to prevent pressure equipment failure.

Remote I/O Block Controller has compact design.

Used in systems requiring rugged remote I/O blocks, A2:M1 suits industrial applications where small package size is required to allow for mounting near hydraulic valves. In addition to CAN (SAE J1939) data link, air-cooled unit features 14 MHz Star 12 microprocessor, 2 analog inputs, and 4 PWM driver 2-wire outputs. Controller is suited for electro-hydraulic systems or machine implement controls.

Motion Control Cards suit extreme motion applications.

Supporting both pulse and voltage output, PCI-bus Models DASP-52504 and DASP-52506 are 4-axis and 6-axis motion control cards designed for both servo and stepper motors. Units support 4 dimension API software structure, as well as RTX drivers and various programs such as VB, VC, BCB, Delphi, and Labview 6.0/7.0, helping users develop and deploy mission-critical applications that run on...

Hot Swap Controller has onboard ADC and I2C interface.

Operating from -12 to -100 V supply, -48 V LTC4261 performs power monitoring by measuring card voltages and currents as well as recording past and present fault conditions. Information in ADC's registers can be used to determine if card is using its allocated power or operating abnormally. Product can also turn supply voltage on and off in controlled manner. Inrush and overcurrent limits,...

Electronic Controller targets OEMs and other integrators.

Featuring die-cast aluminum sealed housing with 210 x 240 mm footprint, Model A5:M2 maintains standard 70-pin connector with individually configurable input pins. Unit is suited for range of off-highway applications, including oil and gas equipment, agricultural equipment and implements, lift equipment, and material handling as well as selected on-road uses such as waste and recycling trucks, and...

Bus Controller suits piping systems with automated valves.

Used in piping systems with 8 or more electrically or pneumatically actuated valves, Bus Control System allows all actuators in system to be controlled by PLC with one pair of wires. Actuators are daisy chained on same pair of wires, with each actuator assigned unique address for identification by PLC. Only designated actuator has ability to read and act on control instructions. In addition to...

Micro PLCs offer communication module options.

Added to Series DL05/DL06 PLCs, D0-DCM Communications Module provides 2 serial ports that support MODBUS RTU, DirectNET, and K-Sequence slave network protocols. Port 1 offers RS-232 interface operating from 9,600 bps to 115.2 Kbps, while Port 2 can be configured for RS-232 or RS422/485 interfaces, and operates from 300 bps to 115.2 Kbps. Suited for ASCII communications, 3-port CoProcessor Model...

Standex Engraving Mold-Tech Offers Nickel Shell Capabilities on a Global Scale

Standex Engraving Mold-Tech is the premier, global supplier for mold texturing and surface finishing. With a full range of services, Standex Engraving Mold-Tech is also the only nickel shell supplier producing in three global locations. See our video to learn more.