
Automatic Balancing Valves operate for life of HVAC system.
Providing constant flow rate of water in HVAC systems, Mesurflo® Valves are factory configured for any flow from 0.5-7,200 gpm, with piping ranging from 0.5-20 in. in diameter. They are designed with virtually silent rubber-based diaphragm, which presses flexibly against plastic-resin opening to control flow. Installation of valve and accompanying strainer and connectors permanently...
Read More »
Directional Control Valve incorporates on-board electronics.
Model 4DP03-3B is rated at 100, 200, or 300 l/min flow rates with 5 bar-per-spool-edge pressure drop, or 500 l/min in double path configuration. It conforms to ISO 4401-07-06-0, CETOP 7, and NFPA 7 standards. Standard M12 connector socket with O-ring seal is supplied for interface connection, providing ramps adjustable up to 10 sec, and 10 V reference voltage for external potentiometer. Optional...
Read More »
Proportional Valve can be programmed via PDA or laptop.
Featuring onboard electronics, PowrFlow(TM) VED03M Valves are available in 6 flow rates from 1-9 gpm, 5 flow metering configurations, and 3 spool-centered conditions, resulting in 90 possible combinations. D03 style valves are rated to 5,000 psi, are equipped with 12/24 Vdc solenoids, and use standard 7-pin connectors at system end. Windows-based screen lets user set all programmable functions...
Read More »
Control Station regulates and maintains water temperature.
Megatron® is designed for hot water systems in new building construction and renovation applications. System components are mounted on galvanized strut. Dial thermometers on hot, cold, mixed, and return piping lines provide complete system monitoring. Mixed water capacity is from 0.5-190 gpm. Integral return piping incorporates circulator, aquastat, check valves, bypass piping, and...
Read More »
6 Engineering & High-Performance Plastics Used for Machined Components
This resource breaks down six of the most commonly used high-performance plastics, properties and common applications, and questions to ask during material selection.
Read More »
Pneumatic Proportional Valve controls speed and velocity.
Featuring microprocessor-driven position control, Model VP60 utilizes glandless spool and sleeve design and delivers more than 250 million operations at full stroke. Zero point adjustment via mini keypad provides application specific method of adjustment for leakage, drift, and offset, while multicolor LED indicates device status. Available with ratings up to 174 psi, Model VP60 features IP65...
Read More »
Spray Valve features stainless steel wetted parts.
Model SV1000SS provides finely controlled spray for low-medium viscosity fluids and coatings. Transfer efficiency is maintained by dual air-control system provided by spray valve controller. Piston-activated needle opens material inlet under low pressure, and secondary pressure source forces air around nozzle to produce spray. At end of operation, needle closes but secondary air remains on...
Read More »
Hydraulic Proportional Valves utilize VCD® technology.
Series D1FP and D1FP*S direct operated control valves use valve-drive technology that actuates spool by using moveable coil over permanent magnetic cylinder to eliminate friction. Used for hydraulic axis positioning as well as controlling force and velocity, D1FP is driven by VCD actuator and can be used in applications with pressure drops up to 4,500 psi. Series D1FP*S provides users with...
Read More »Control Valves suit industrial refrigeration applications.
Formed from steel, ICV weld-in control valves are offered in servo and digital motorized versions. Both use same valve body, which has no internal bearing surfaces. Seat and all operating parts are contained in replaceable function module. Single- and 3-pilot bonnets are offered for servo-operated versions. With working pressure range to 725 psig, products perform as pressure regulating valves,...
Read More »
Control Valve conforms to ANSI B 16.34 and ASME VIII.
Available in sizes from 1-8 in., C Series control valves offer pressure ratings conforming to ANSI 300 and ANSI 600, and come in carbon steel, alloy steel, or stainless steel body materials. Cage-guided balanced plug provides control over high differential pressures, and 1-, 2- and 3-stage designs are offered to minimize cavitation and aerodynamic noise. Modular structure enables single valve...
Read More »
Control Valve combines valve, actuator, and positioner.
FCV 1 in. control valve incorporates LVDT for detecting position; actuator; and electronics and pneumatics positioner to open and shut valve. Available in normally open or normally closed versions, product operates with command signal of 0-10 V or 4-20 mA. Valve position and Cv changes linearly over 0-19 Cv range.
Read More »
Custom Fabrication & Machining Services with Over 30 Years of Experience
As a trusted manufacturer to customers across a broad range of industries, Key Gas Components is a premier provider of CNC machining and tube fabrication. Our entire organization is quality driven and customer-centric, with broad-based manufacturing capabilities that can accommodate the most challenging requirements. See our video to learn more.
Read More »