Locking Key Slot attaches standoffs and fasteners to PCB.
Studs

Locking Key Slot attaches standoffs and fasteners to PCB.

LKS can be used in place of pressed in metal screw insert to attach fasteners to circuit boards and panels. It is easily installed and removed by hand from same side of panel. It has low insertion force yet pullout force exceeds strength of most standard PC boards. Slot is made of Nylon 6/6 to fit panels and circuit boards 0.062 in. thick. LKS holds standoffs, wire ties, wire routing clips and...

Read More »
Air Bag Lifting Device lifts up to 72 tons.
Lifts

Air Bag Lifting Device lifts up to 72 tons.

MaxiForce compressed air-powered lifting device is available in 13 models from 6 x 6 in. to 36 x 36 in. with capacities of 1.5 to 72 tons. Applications include changing tires, shifting pipelines, and lifting loads. It needs less than 1 in. of insertion space to be set and inflated, and inflates in less than 60 seconds. Bag's positive grip furnishes optimal friction, so it can be put to use on...

Read More »
Board Stackers offer design flexibility.
Stackers

Board Stackers offer design flexibility.

On .100 in. pitch, single, double and triple row through-hole headers (MTSW Series) and stackers (ZW Series), surface mount board stackers (HW Series) and shrouded headers (ZSS Series) are available for board stacking. For micro pitch, board stackers are available on .8mm pitch (AW Series), 1mm pitch (MW Series), .050 in. pitch (FW Series), .050 in. x .100 in. pitch (DWM Series) and 2mm pitch (TW...

Read More »
Cylinders

Rodless Pneumatic Cylinder works in temperatures to 500 ºF.

OSP Series Thermocylinder can be used for door opening and transfer in extreme temperature applications. It uses heat transfer and thermodynamic principles to allow coolant to pass through entire length of cylinder. As coolant passes through, heat energy is absorbed and barrel behaves similar to water jacket. This keeps heat away from cylinder bore where plastic and rubber parts are used.

Read More »
Nailers

Framing Nailer handles lengths from 2-3/8 to 3-1/2 in.

Model NR90AC2 Full Head Framing Nailer has 1-piece solid extruded aluminum magazine, die-cast aluminum body, and air inlet dust filter. It operates at pressures of 70 to 100 psi, and is capable of driving up to 3 round head nails per second. Features include aggressive nail push lever, idling protector, depth-of-drive adjustment dial, and 360° exhaust. It can handle 50 to 60 nails (2...

Read More »
Nailers

Framing Nailer fires at up to 3 nails per sec.

NR83AA2 Clipped Head Framing Nailer features push lever that prevents nail jamming, and one-piece rear-loading aluminum magazine which holds up to 96 nails. It weighs only 8.4 lb and includes band rubber grip. Toe push lever resembling a claw grips wood surface being nailed and eliminates slippage when driving nails in slanted direction. NR83AA2 uses 0.113 to 0.131 in. dia nails in lengths from 2...

Read More »
Interconnects are available with 10 to 100 I/Os.
Connectors

Interconnects are available with 10 to 100 I/Os.

TFM and SFM Series .050 in. pitch interconnects are designed for applications requiring blind mating and/or high number of mating cycles. They are available with board spacings from .236 to 1.472 in. Three-finger Tiger-Eye contacts in SFM Series are stamped and formed with soft Beryllium Copper and heat-treated to optimize spring properties. Tiger Eye LITE three-finger contact is also available...

Read More »
Shielded Connector minimizes electrical interference.
Connectors

Shielded Connector minimizes electrical interference.

Micro-Link connector has 360° aluminum mylar foil shield to minimize electrical interference that can disrupt signal from connector to control device. Gold-plated contacts provide long life, improved conductivity, and corrosion resistance. Rated NEMA 6P and IP 68, connectors can be used for quick disconnect of proximity sensors, photoelectric sensors and switches, hydraulic and pneumatic...

Read More »
Inserts

Milling Cutters work fast and efficiently.

Fix-Perfect aluminum milling cutter inserts have on-edge orientation and 34 deg positive rake angle. This geometry reduces insert edge buildup, improves tool life, and provides free cutting action that makes it possible to machine thin-walled parts. Inserts are available in uncoated, coated, and polycrystalline diamond versions.

Read More »
Connectors allow for off-axis insertion.
Connectors

Connectors allow for off-axis insertion.

P-lok® connectors with integrated RADSOCK® socket technology provide positive-locking, spring-loaded coupling. 8 AWG P-lok contacts handle currents up to 69 A while size 4 AWG handle up to 120 A. Features include hyperbolic stamped grid configurations and Push-Pull systems. Thermal rise data after 500 cycles of durability is as follows: Size 8 AWG socket has 38°C at 46 A; Size 4...

Read More »

All Topics

COVID-19 Response Suppliers COVID-19 Response:
Can Your Company Help Provide Critical Supplies?

We are using the power of our platform to aid in the mass shortage of critical supplies. If your company can help provide supplies, capabilities, or materials for products such as N-95 Masks and Tyvek SuitsPlease let us know.

COVID-19 Response Suppliers