Wheeled Dozer offers compaction and maneuverability.
Bulldozers

Wheeled Dozer offers compaction and maneuverability.

Rubber-tired Model WD600-3 pushes with 485 flywheel hp at 2,000 rpm and offers maximum rim-pull up to 94,300 lb. It features Tier 2 compliant SAA6D170E-3 engine and fully automatic shift transmission. Fully hydraulic, wet-disc braking system is completely sealed to lock out contaminants. A 10 cu yd straight blade is standard. Dozer is suited for mining, coal stockpile, woodchip, and general...

Read More »
Crawler Dozers feature hydrostatic steering system.
Bulldozers

Crawler Dozers feature hydrostatic steering system.

Models D65EX/PXIWX-15 and D85EXIPX-15 are mid-sized crawler dozers equipped with Tier II compliant SA6125E-3 engine. D65 operates with 190 hp at 1,950 rpm, while D85 pushes with 240 hp at 9,000 rpm. Blade capacities range from 4.8-7.34 yd-³ for D65 and 6.8-9.2 yd³ for D85. Powered by independent hydraulic pump with engine power transmitted to both tracks, outside track is allowed to move...

Read More »
Aligners

Laser Alignment System improves manufacturing efficiency.

Dual-Axis Microgage 2D can measure horizontally and vertically at same time. It provides straightness, flatness, parallelism, and squareness measurements to 0.001 in. over distances of 50 ft. System will monitor mechanical misalignment and runout, align rails and slides, position machinery sub-assemblies, and align bores and drive shaft mechanisms. It can be attached to PC or laptop for...

Read More »
Tap Aligning Center simplifies hand tapping.
Aligners

Tap Aligning Center simplifies hand tapping.

Equipped with No. 2 Morse taper, Tap Aligning Center has spring center used to align taps when hand tapping in lathes or drilling machines. Suited for awkward tapping operations, product does not require user to constantly adjust center. Physical characteristics include hardened 5/16 in. dia center, 1 in. plunger travel, and overall length of approximately 5-½ in.

Read More »
Filters Buying Guide
Sponsored

Filters Buying Guide

It can often times feel overwhelming selecting the right filtering product for your needs. This buying guide gives the basic definition of what a filter does, and goes on to outline in more detail the various types of filters that are available on the market, and what they do.

Read More »
Snow Plow Control Holder offers simple installation.
Plows

Snow Plow Control Holder offers simple installation.

Control Holder provides means of adding controls to vehicles without drilling directly into truck console. It installs by fitting directly over seats of vehicle, and installation or removal of device takes approximately 30 seconds. Control holder will fit virtually all trucks with typical seats, although some truck models may require removal of cup holder.

Read More »
Skid Steer Hammer Attachments offer more power with less weight.
Hammers

Skid Steer Hammer Attachments offer more power with less weight.

Breakers range in weight from 430-1,100 lb. Smallest model has tool energy rating of 70.11 lb-ft/blow, while largest breaker has rating of 468.63 lb-ft/blow. Valve system uses less oil flow to do same job as higher flow breakers. Air check valve system allows units to be submerged in water while working. Shorter size increases operator visibility in small tight areas.

Read More »
Suction Diffusers increase flow-straightening capabilities.
Straighteners

Suction Diffusers increase flow-straightening capabilities.

Available with 1, 3, or 5 pipe diameters of flow straightening, products reduce turbulence and protect against particles. Units incorporate strainer, elbow, and pipe-reducer functionality along with quick-release cover and 1/8 in., stainless steel, perforated screen with 20-mesh liner. Diffusers are offered in cast iron, configured to replace 90° elbow, as well as in fabricated carbon steel or...

Read More »
Crawler Dozers feature hydrostatic steering system.
Bulldozers

Crawler Dozers feature hydrostatic steering system.

Models D65EX/PXIWX-15 and D85EXIPX-15 are mid-sized crawler dozers equipped with Tier II compliant SA6125E-3 engine. D65 operates with 190 hp at 1,950 rpm, while D85 pushes with 240 hp at 9,000 rpm. Blade capacities range from 4.8-7.34 yd3 for D65 and 6.8-9.2 yd3 for D85. Powered by independent hydraulic pump with engine power transmitted to both tracks, outside track is allowed to move faster...

Read More »
Repair Component evaluates/repairs ASME pressure vessels.
Maintenance and Repair Services

Repair Component evaluates/repairs ASME pressure vessels.

PMCap provides code-compliant, non-intrusive, permanent repair of pressure boundaries. Metal Loss Evaluation Assessment (MLEA) charts, generated by Fitness for Service software program, provides for immediate field assessment of vessel to determine ASME Code compliance. Supplied as Code material or certified PART for vessel alteration, customized repair component is welded to outside surface...

Read More »
Earthmovers offer max capacity of 18 cubic yards.
Scrapers

Earthmovers offer max capacity of 18 cubic yards.

Series 18D provides 2-valve sequence operation and CAT cutting bits. Four 20.5 x 25 tires offer maximum flotation. Heavy duty cylinders have 3 in. rams and -¾ in., 4000 psi pressure hoses. Design provides rapid, clean swingfloor ejection system. MD yoke quickhitch is standard; HD 360° swivel quickhitch is optional. Transport width is under 12 ft.

Read More »
Dodge® Raptor Coupling Now Available in Three Larger Sizes
Sponsored

Dodge® Raptor Coupling Now Available in Three Larger Sizes

The Dodge Raptor coupling epitomizes the innovation and value that has made Baldor a world leader in industrial electric motors. For almost 100 years Baldor has been the go-to source for industries across the globe. The Raptor coupling is just one example of our dedication to engineered excellence and commitment to providing value and performance. See our video to learn more.

Read More »

All Topics