Angle Encoder features smallest possible reversal error.
Incremental angular encoder, Model ERP 880 features circular scale with 90,000 grating periods. Graduation is scanned interferentially so that after signal acquisition, 180,000 sinusoidal signal periods are available for evaluation. System accuracy is Ã-
Read More »Integrated Circuit acts as replacement for RF receivers.
Offered as alternative to discrete superregen receivers, QwikRadio(TM) MICRF008 RF receiver eliminates need for production tuning. Product incorporates sweep mode, which enables superheterodyne receivers to sweep RF bandwidth wide enough to emulate capture bandwidth of superregen receivers (9 MHz). Offered in 8-pin SOIC packaging, product has 300-440 MHz frequency range, 4.8 kbps max data-rate.
Read More »Employee/Pedestrian Passageways protect against the elements.
Pedestrian/flow management passageways, fabricated from structural steel tubing, are designed to protect employees, pedestrians, and turnstiles from harsh exterior elements. Shelters come fully assembled with glazing, lighting, and optional heating units. Pre-assembled shelters are then positioned over newly installed or existing turnstile equipment.
Read More »Interface Transceiver Chipset supports 3.3 V logic.
Models LTC2847/LTC2845 come in 5 x 7 mm QFN packages and provide multi-protocol serial port for LAN and WAN equipment with remote access ports. Two-chip solution includes configurable transceivers for data and clock signals with on-chip switchable termination resistor networks and transceivers for control signals. Units operate from single 5 V supply and support RS232, RS449, EIA-530, EIA-530-A,...
Read More »Steel Wire Selection Guide for Various Applications
Download this eBook to learn about how steel wire products can be used for a variety of applications.
Read More »Home Entertainment Speakers offer contemporary design.
Velocity Line includes bookshelf, floor-standing, and surround-sound speakers, as well as powered subwoofers. One-piece woofer frame is molded as part of speaker baffle surface. Basket is top layer of 3-part baffle assembly with dense, highly damped center section and 3/4 in. MDF. Injection-molded polypropylene cones are layered with Vapor Deposited Titanium for smooth, extended midrange...
Read More »Dip-Flux Feeder facilitates flip chip assembly.
Dip-Flux Feeder picks up component from waffle tray, stick feeder, or tape feeder, then dips component, leads, or BGA balls into rotating flux bath. It then places component or flip chip onto board or substrate. Fixed squeegee in rotating flux bath ensures constant flux wave height. Laser sensors detect approaching components and halt squeegee rotation for duration of dipping process. Feeder is...
Read More »Signal Horn is suited for indoor and outdoor use.
With protection rating of IP 65, Signal Horn 573 measures 207 x 178 x 103 mm and has PC/ABS housing that accommodates one continuous tone horn capable of 105 dB sound output. System includes horn with removable hood, cable gland for pull relief, and concealed fixing screws.
Read More »Wafer Positioner offers integrated 3-axis tip/tilt stage.
Designed for 300 mm wafer processing, DynamYX GT air-bearing wafer positioning system offers 6 axes of precision motion control. Machine includes silicon carbide stage, single plane system architecture, and low-profile design that reduces center of mass to minimize error from deflection or angular deviation. Alignment is achieved via Z-Tip-Tilt stage integrated on carriage in non-contact design....
Read More »Receiver simplifies alignment of access points and bridges.
Beetle(TM) 802.11b Receiver with antenna alignment kit allows for antenna alignment of point to multi-point solutions. Product comes with hardware and software for surveying and optimizing STAs (Client Cards) as well as Access Points. Product measures correlated signal strength, Packet Error Rate, and power output from base stations with in-line attenuation. Unit also captures all MAC addresses...
Read More »Subwoofer Systems have unobtrusive design.
SUB 200 & SUB 100 In-Wall Powered Subwoofer Systems provide invisible home theater and music solution. Positive Clamping System creates rigid barrier around speaker baffle, trapping vibrations. Model IW-200 has dual 8 in. mica/graphite polypropylene cone drivers and 72 x 14 3/8 x 3 3/8 in. enclosure box. Model IW-100 features 7 in. mica/graphite polypropylene cone drivers and 48 x 14 3/8 x 3 3/8...
Read More »SRG Global Coatings Enhance Surface Durability, Efficiency, Design Flexibility
SRG Global's automotive coatings enhance the structural integrity of the finished part while also improving vehicle efficiency. Check out our video to learn more.
Read More »