Hose Clamps have 1-piece design.
Hose Clamps

Hose Clamps have 1-piece design.

Constant Tension Light Band self-compensating hose clamps are manufactured using austempering method, a heat treating process that ensures strength and eliminates brittleness. With single piece construction that provides leakproof connections, clamps are suited for applications in small engines, agricultural & utility vehicles, automotive systems, and appliances.

Read More »
Pin Locating Clamp features fully enclosed design.
Power Clamps

Pin Locating Clamp features fully enclosed design.

Pneumatically powered actuator, Series PLC locates, clamps, and supports parts in weld areas. Fully enclosed design provides protection against weld slag and other contaminants, while built-in locking mechanism locks pin in any position to secure parts if air pressure is lost or removed. Available in 2 sizes with 5 pin size choices and 2 pin styles, Series PLC provides 12.5 mm max clamping...

Read More »
Swing Arm Clamps are offered in 25 and 32 mm bore sizes.
Clamps

Swing Arm Clamps are offered in 25 and 32 mm bore sizes.

Available in 4 bore sizes from 25-50 mm, Series PB employs hardened helical spline and 3 hardened drive balls. Keyed interface between rod and arm ensures location and facilitates installation, while rear plug allows arm position to be adjusted up to 90°. Equipped with anti-backlash arm and guide, switch-ready products enable users to change clamps from left to right rotation by changing...

Read More »
Hand (Tool) Clamps

Slide Pivot Clamp offers max pressure of 7,500 psi.

Available in 3 sizes, double-acting Slide Pivot Clamp allows workpieces to be inserted from above without impediments, since clamping lever can be moved into small recesses. Piston force is transferred 180° by clamping lever and is available as clamping force with virtually no loss of efficiency. Unit is suited for clamping on machines when high clamping forces are required with minimal...

Read More »
Clamping System suits short run jobs with different set-ups.
Hand (Tool) Clamps

Clamping System suits short run jobs with different set-ups.

Manually-operated Pull Block activates clamps when normal method of tightening clamp is not allowed. Any clamp that requires straight jaw can be mounted on unit. Face plates and drive plates can be exchanged, so different set-ups can be done on same block. Each heat-treated and ground piston operates independently and only requires Â-¼ turn to tighten or loosen with standard socket wrench.

Read More »
Cable Hangers

Clamps, Straps, and Hangers fasten electrical conduit.

Clamps, straps, and hangers assist contractors in running and anchoring electrical conduit. Clamps are formed from malleable iron with galvanized finish, and accommodate conduit in trade sizes from Â-½-6 in. They secure rigid or flexible metal conduits, and IMC or EMT running across, parallel, or perpendicular to beams, channels, cable tray, and angle supports. Steel hangers and snap-type...

Read More »
Tube Clamps and Linear Actuators work in modular systems.
Hose Clamps

Tube Clamps and Linear Actuators work in modular systems.

Metric Tube Clamp Connector Components are used to construct fixtures, machine guard units, equipment bases, and operating systems using standard round and square tubing. They are offered as one-piece split or multi-part tube clamp connectors made of aluminum with various finish options. Manually Driven Linear Actuators consist of guide tube, threaded internal spindle, and follower nut. They are...

Read More »
Clamping Module features holding forces to 75,000 N.
Power Clamps

Clamping Module features holding forces to 75,000 N.

Measuring 196 mm in dia, NSE 196 module is mechanically clamped and pneumatically opened, allowing clamped system to be moved in clamped state without interference from air lines. Clamping pin has a 61 mm dia through hole, which makes it possible for workpiece to protrude through clamping system. To facilitate orientation of fixture plates, module also comes with 12 mm precision bore on face.

Read More »
Clamping Vise is resistant to contamination.
Hand (Tool) Clamps

Clamping Vise is resistant to contamination.

KONTEC KSL stationary clamping vise allows cubic workpieces to be clamped onto universal vertical machining centers or any 4th or 5th axes table. Available in 3 sizes with base jaw widths of 100, 125, or 160 mm, mounting holes located in jaw allow mounting of workpiece stops from both sides. Actuation is done from side of the fixed jaw via allen key equipped with ratchet, and vise securely clamps...

Read More »
Manual Clamps provide safety and ergonomic benefits.
Hand (Tool) Clamps

Manual Clamps provide safety and ergonomic benefits.

Toggle-Lock Plus Clamps help to maintain over-center toggle position in applications where there is likely to be movement or vibrations, such as transfer lines. Eliminating pinch points, units feature bushings at major pivot points and stop point locations at base. Spindle contacts workpiece in vertical position to help stop marring or movement, while clamping arm completely clears workpiece to...

Read More »

All Topics

COVID-19 Response Suppliers COVID-19 Response:
Can Your Company Help Provide Critical Supplies?

We are using the power of our platform to aid in the mass shortage of critical supplies. If your company can help provide supplies, capabilities, or materials for products such as N-95 Masks and Tyvek SuitsPlease let us know.

COVID-19 Response Suppliers