Chucks and Collets

RÖHM Power-Operated Chucks Deliver Secure Holding for Gear Grinding
Chucks and Collets

RÖHM Power-Operated Chucks Deliver Secure Holding for Gear Grinding

SUWANEE, Ga., Nov. 28, 2016 – RÖHM Products of America now offers a powered external clamping chuck for gear surface face grinding. The KZF-S collet chuck is especially well suited for clamping gears/workpieces that have an external plane or gear teeth geometries accessible from the outside. Additionally, the chuck allows face and ID diameters to be turned or ground concentric to outer gear...

Read More »
Customized Chuck to the Rescue!
Chucks and Collets

Customized Chuck to the Rescue!

Island Park, NY... Northfield Precision Instrument Corporation is a leader in the design and manufacture of precision workholding chucks. When a good customer required a chuck to hold parts to be mounted to a Studer Grinder for contour grinding into special cutting tools, they turned to Northfield for help. Northfield’s engineers customized their Model 650 chuck to use only one jaw for...

Read More »
ROTA-S Flex Maximizes the Potential of Your Milling and Turning Machines
Chucks and Collets

ROTA-S Flex Maximizes the Potential of Your Milling and Turning Machines

The ROTA-S flex is a highly flexible manual chuck for machining a wide variety of workpieces on milling and turning machines. The ROTA-S flex has all the same beneficial features as the tested and proven ROTA-S plus in addition to extended guideways, transforming it into a large, versatile, light-weight chuck. The weight of the ROTA-S flex is approximately 60% less than that of a conventional...

Read More »
Heavy Duty Machining - but Safe
Tool Holders

Heavy Duty Machining - but Safe

The importance of the tool holder is still understated, especially when it comes to roughing and heavy duty machining. Metal removal rates in these types of processes are absolutely crucial for the productivity of the machining operation. By using special shrink fit chucks with drive pins and spiral grooves in the tool shank it is now possible to perform high-feed full slotting of up to 2 x D (50...

Read More »
Pneumatic Power Chuck offers accelerated clamping.
Chucks and Collets

Pneumatic Power Chuck offers accelerated clamping.

Self-contained ROTA TB2, used for machining rods and pipes, is available with through-hole of up to 560 mm. With air pressure of 6 bar, it is possible to achieve clamping forces of up to 280 kN. Base jaw guidance is equipped with seal to prevent penetration of contamination, and base jaws are optimized for minimal loss of centrifugal force. Sizes from 470–1,000 mm with bore diameters from...

Read More »
Singular Chuck features 2 sets of flexing jaws.
Chucks and Collets

Singular Chuck features 2 sets of flexing jaws.

Customized Model 650 chuck features 2 sets of flexing jaws that are hardened and ground as well as wire cut to allow compensation for out of round parts. Hardened and ground stop locates part axially, and second set of jaws and stop gripÂ- small bore (.750 dia) and pull part onto hard stop. This ensures part is properly seated. To keep chips out, slots are filled with rubber.

Read More »
High-Accuracy, 3-Jaw Chuck has side-loading design.
Jaws

High-Accuracy, 3-Jaw Chuck has side-loading design.

Balanced by 2 weights, Model 620 chuck is side loaded between jaws as necessitated by part geometry and needs to rest on small boss at end of slot. This 6 in. dia, 3-jaw chuck with 1 in. dia counterbore (hidden) also features sub-jaws and inserts. When removed and re-installed, changeable insert stop pads repeat to 1/10,000 TIR. Accuracies range from 0.001–0.00001 in.

Read More »
ROHM to Feature Workholding Technologies that Maximize Machine Time at IMTS
Clamping Systems

ROHM to Feature Workholding Technologies that Maximize Machine Time at IMTS

SUWANEE, Ga. – At IMTS 2016 in booth W-2528, RÃ-¶hm Products of America will show its strength as a one-stop clamping and gripping supplier by presenting a wide range of workholding innovations. Among the products on display will be two of the company’s newest solutions that fulfill industry demands for increased efficiency, ergonomics, weight reduction and convenience. Manufacturers in...

Read More »
Milling Chuck eliminates pullout during heavy-duty milling.
Chucks and Collets

Milling Chuck eliminates pullout during heavy-duty milling.

As heavy-duty milling chuck with fully concentric clamping, BIG Daishowa Mega Perfect Grip eliminatesÂ- concerns about end mill pullout under heavy torque loads when used with heat resistant super alloys (HRSAs). System, based around milling cutters with standard Weldon flat (ASME B94.19-1997), does not require special grinding or threading of milling cutter. Three key grip grooves in chuck...

Read More »
Milling/Drilling Chucks increase machining speed, tool life.
Chucks and Collets

Milling/Drilling Chucks increase machining speed, tool life.

Optimized for concentricity (≤3 Â-µm), machining speed, and tool life in milling and drilling applications, FPC Mill/ Drill Chucks feature 1:16 worm gear and deliver 3 tons of traction force. Design and body provide 100% holding power for maximum rigidity, while collet-cone assembly absorbs nearly all vibration for maximum dampening. While 3xD tool length promotes accuracy, transferable...

Read More »
Solder Redefined
Sponsored

Solder Redefined

Indium Corporation has developed a new twist on traditional solder by developing a composite with a reinforced matrix internal structure. The result is a solder with increased strength and reliability. Check out this video to learn more about the mechanics behind the groundbreaking technology.

Read More »

All Topics

COVID-19 Response Suppliers COVID-19 Response:
Can Your Company Help Provide Critical Supplies?

We are using the power of our platform to aid in the mass shortage of critical supplies. If your company can help provide supplies, capabilities, or materials for products such as N-95 Masks and Tyvek SuitsPlease let us know.

COVID-19 Response Suppliers