
Grease Caddy helps prevent over lubrication conditions.
Ultraprobe 201 Grease Caddy can be mounted directly on grease gun or put in holster and worn on belt. Magnetic mount enables placement of probe on bearing housings, and sensing element detects ultrasound while filtering out low-frequency signals. Monitoring changes in ultrasound levels as bearings are lubricated enables users to know when enough lubricant has been added. Product also has...
Read More »Oiler minimizes friction during engine startup.
AMS-Oiler recharges engine's bearing with 160 cc of lubricant in first 2 minutes of engine startup. During winter, it saves fuel and wear and tear on engine's first five minutes. Oiler eliminates need to run engine during a lunch break or over night. Self-contained system is constructed of anodized aluminum and carbon steel. Life cycle exceeds one million starts.
Read More »
Lubrication System uses infrared photo sensor.
Infrared Lubrication System is equipped with solid-state PLC, 3-way solenoid valve, bank of PurgeX® pumps, power supply, and NEMA 12 enclosure. Independent pump operation allows individual adjustment of flow to each lube point from 0-.012 cu in./cycle. Clear, polycarbonate, -½ gal reservoir, with hinged top lid, feeds system and allows for visual confirmation of fluid level. System is suitable...
Read More »
Grease Meter features maximum working pressure of 700 bar.
Using measurement principle based on oval gearwheel, Grease Meter provides tool to lubricate each bearing per manufacturer's recommendations. It can be fitted to all normal hand pumps and valve handles for grease lubrication. Outflow quantity is indicated in g, cm-³, oz, or fl-oz on 4-figure, backlit display. Meter has total counter in tons.
Read More »
Mitigating Supply Chain Risks for Sheet Metal Components
This ebook provides an overview into mitigating supply chain risks for sheet metal components.
Read More »
Closed System Oiler includes sight gage.
Opto-Matic Oiler is suited for equipment where constant level in oil sump must be maintained. Closed design prevents contamination and spillage. Adjustable collar allows oil level to be externally adjusted to desired level. A 1/8 NPT port is provided for vent line back to housing to allow pressure balancing between oiler and housing.
Read More »
Handheld Oiler provides protection for threading dies.
RIDGID® Model 418 includes heavy-duty, abrasion- and rust-resistant reservoir that resists impact without denting, cracking, piercing, or permanently deforming. Reservoir's integral molded body design, combined with flat hose port, eliminates leaks at hose-reservoir connection. Fastener-less, twist-and-lock mechanism allows user to lock drip pan into place. Pump delivers 50% more thread cutting...
Read More »
Lubrication System applies oil to stock and dies.
MicroCoat® 780 Series provides steady or pulsed lubrication up to 300 times/min. It includes valve, valve controller, and 1, 5, or 20 gal tank. Valves use low volume, low pressure air to evenly coat stock or dies with fine, consistent film of oil. One valve covers area from 3/16-6.5 in. wide. If wider coverage is required, additional valves can be mounted side-by-side. Stroke control adjustment...
Read More »
Lubrication Devices suit hygienically clean applications.
Gas and motorized G-Power and M-Power single-point lubricators connect to existing grease or lubrication fittings to apply lubricant to bearings, chains, guideways, gears, and seals. They dispense precise amount of grease over set period of time. Available in 3 models, G-Power gas lubricators suit high humidity/corrosion applications. M-Power motorized lubricators offer reusable drive motors,...
Read More »
Lubrication System services 2 points.
Using pre-filled, replaceable cartridges, Model 240 HPS (High Pressure System) provides 350 psi output pressure, which allows lubricator to be mounted out of harms way in applications involving high temperature or heavy vibration. Supplied with mounting bracket and battery pack, 2-Point MEMOLUB Lubrication System suits applications involving 2 bearings such as fans, motors, pumps, or other...
Read More »
Assessment Device senses lubrication conditions.
Portable Ultraprobe 201 Grease Caddy informs users of lubrication conditions in bearings by sensing high-frequency emissions produced by bearings. It translates them into audible range where they are heard through headphones and seen on meter. Amplitude levels can be set to determine when to lubricate. Unit attaches to most common grease guns, swivels for left and right handed users, and adjusts...
Read More »
More performance and functionality for Sinumerik 828D CNC
Siemens new SINUMERIK 828D ADVANCED, SINUMERIK 828D and SINUMERIK 828D BASIC sets the standard for productivity enhancements of turning and milling operations on standardized machines and simplify the automation of grinding machines. See our video to learn all about it.
Read More »