Ceramics

Substrates

Ceramic Substrate suits thick-film applications.

Designed to address miniaturization and higher-power applications, DuraStrate consists of fine-grained (1.5-2.0 micron) microstructure material optimized for biaxial flexural strength, consistent thicknesses, camber flatness, and aged adhesion. Ceramic substrate material is designed for optimal performance in very thin (10-15 mil) varieties of thick-film substrates.

Read More »
Ceramics

Ceramic Material is suited for jigs and brazing fixtures.

Resistant to chemicals, oxidation, wear, and thermal shock, M120F Aluminum Silicate can be machined into intricate shapes and held to close dimensional tolerances. Formulation facilitates machinability in product's green state, and working temperature is rated up to 1,150°C. Product is fully fired at high temperatures to create hard ceramic material, which makes it suited for use in...

Read More »
Composites

Morgan Electro Ceramics Showcases Piezoelectric Composite Components at Md&M East

Morgan Electro Ceramics (MEC), a division of Morgan Technical Ceramics, will showcase its new piezoelectric composite components at MD&M East, held June 11-14, 2007 in New York, NY in booth #858. Components manufactured with piezocomposite materials offer improvements over traditional transducer materials, which result in increased acoustic performance for medical applications, including medical...

Read More »
Ceramics

CoorsTek Introduces Diffuse Reflecting CeraLase(TM) Ceramics for Laser Equipment Components

New material combines high diffuse reflectance with the high-temperature durability of ceramics to provide superior performance in high power, solid-state laser applications. December 7, 2006 - Golden, CO - CoorsTek, one of the world's largest technical ceramics manufacturers, today officially announced introduction of its new CeraLase(TM) ceramic materials developed specifically for laser...

Read More »
Alumina Ceramic withstands temperatures to 3,000°F.
Alumina (Aluminum Oxide)

Alumina Ceramic withstands temperatures to 3,000°F.

High-density, full-fired Aremcolox(TM) 502-1400 96% pure alumina ceramic exhibits abrasion, corrosion, electrical, chemical, and erosion resistance. Compressive strength is 340,000 psi, flexural strength is 46,000 psi, and dielectric strength is 225 V/mil. Aremcolox(TM) 502-1400 parts are fabricated to close tolerances through injection molding, isostatic pressing, and diamond machining...

Read More »
Ceramics

Ceradyne, Inc. Receives $13.3 Million Ceramic Body Armor Order; for U.S. Marine Corps, Special Operations Forces

COSTA MESA, Calif.--Aug. 23, 2006--Ceradyne, Inc. (Company) (Nasdaq:CRDN) received two ceramic body armor delivery orders totaling $13.3 million from the U.S. Marine Corps., Quantico, Virginia, and U.S. Special Operations Command, MacDill Air Force Base, Florida. These orders for ESAPI and Side Plates are scheduled for delivery from third-quarter 2006 through early 2007. Dave Reed, Ceradyne...

Read More »
Ceramics

Ceradyne, Inc. Receives $13.3 Million Ceramic Body Armor Orders for U.S. Army

COSTA MESA, Calif.--Sept. 11, 2006--Ceradyne, Inc. (Company) (Nasdaq:CRDN) received two ceramic body armor delivery orders totaling $13.3 million from the U.S. Army, Aberdeen Proving Ground, Maryland. The orders are for $9.9 million of ESAPI and $3.4 million of ESBI (side plates) to be shipped in fourth-quarter 2006. These new delivery orders will be shipped against larger indefinite...

Read More »
Ceramics

Ceradyne, Inc. Receives $9.1 Million ESAPI Orders

COSTA MESA, Calif.--Sept. 12, 2006--Ceradyne, Inc. (Company) (Nasdaq:CRDN) received new delivery orders for approximately $9.1 million of its lightweight ceramic body armor, enhanced small arms protective inserts (ESAPI). These orders were placed by the Defense Supply Center Philadelphia (DSCP) for delivery late this year and early 2007. These orders were placed against a larger indefinite...

Read More »
SiC Ceramic helps extend semiconductor equipment life.
Ceramics

SiC Ceramic helps extend semiconductor equipment life.

Targeted for semiconductor processing equipment manufacturing, Performance Silicon Carbide (SiC) is manufactured utilizing chemical vapor deposition (CVD) process. Available in ultrapure and low electrical resistivity grades, material properties include high purity, stiffness, thermal shock resistance, and thermal conductivity. Low electrical resistivity Performance SiC, when used in heating...

Read More »
Machinable Ceramic can be used in applications to 2,100°F.
Ceramics

Machinable Ceramic can be used in applications to 2,100°F.

Used to produce ceramic parts, Aremcolox(TM) 502-1100 works in oxidizing, reducing, or vacuum atmospheres and will not outgas in ultra high vacuum. Machinable alumino-silicate ceramic exhibits compressive strength of 25 Kpsi, dielectric strength of 100 V/mil, and thermal conductivity of 9.0 BTU-in/hr-ftÂ-²-°F. Machined using conventional tooling, product has coefficient of thermal...

Read More »
Triad's JSU Series of Power Supplies Provide Robust, Low Cost Solutions
Sponsored

Triad's JSU Series of Power Supplies Provide Robust, Low Cost Solutions

Triad Magnetics is an established leader in power supply innovation, offering product lines that span a wide range of diverse industries and applications. Adding to their long list of successful product launches, Triad announces the release of the new cutting-edge JSU Series of power supplies. To learn about all of its advantages and advanced features, see our video.

Read More »

All Topics