Centrifugal Pumps

Condensate Pumps eliminate flaring to atmosphere.
Centrifugal Pumps

Condensate Pumps eliminate flaring to atmosphere.

Closed-Drain leak-tight condensate re-injection pumps provide flow rates from 10 to 157 barrels/hr. They have two PTFE diaphragms that are sandwiched and operate in balance, providing double containment with zero-leakage, run-dry tolerance, and overload protection. Unaffected by dirt, moisture, and contaminants, pumps accept high suction pressure up to 5,000 psi and control fluid being drawn off....

Read More »
Centrifugal Pump is offered in 316 stainless steel.
Centrifugal Pumps

Centrifugal Pump is offered in 316 stainless steel.

Flomax 8 self-priming pump with viton seals offers corrosion resistance and chemical compatibility with difficult fluids. Capable of delivering head pressures up to 100 ft and flow rates to 160 gpm, it provides max suction lifts of 25 ft. Available in kit form, Flomax 8 pumps can be mixed and matched with different motors. Pump pack options include pedestal, engine or motor mounted models, and...

Read More »
Sump Pumps replace other pumps without plumbing changes.
Centrifugal Pumps

Sump Pumps replace other pumps without plumbing changes.

SP33 1/3 hp and SP50 1/2 hp sump pumps have cast iron vortex impeller, stainless steel shaft, silicon carbide seals, thermal overload protection, and permanent split capacitor motor. Piggyback-mounted switch eliminates need to pull pump to check for pump failure. Adjustable vertical or swing floats are available to accommodate varying conditions. Pumps interchange with competing sump pump models,...

Read More »
Centrifugal Pump provides leak-free operation.
Centrifugal Pumps

Centrifugal Pump provides leak-free operation.

Sealless RD Series provides constant flow over wide range of pressures up to 15 psi. It has brushless 24 Vdc motor and can be located close to fluid reservoir. Quiet running, and rated for over 25,000 hours operation, canned-motor pump directly drives rotor magnet incorporating impeller. Casing completely seals pump chamber from exterior. Flow rates range from 1.1 to 5.3 GPM in footprints from...

Read More »
ANSI Pumps handle dirty and reclaim process fluids.
Centrifugal Pumps

ANSI Pumps handle dirty and reclaim process fluids.

Stan-Cor Series non-metallic centrifugal pumps are suited for pumping abrasive and corrosive process fluids. They provide total dynamic head to 350 ft and flow rates to 700 GPM. Solid Kynar or Teflon(R) pump head provides chemical compatibility and abrasion resistance. They are equipped with concentric casing designs, heavy-duty drive shaft, and duplex contact thrust bearings.

Read More »
Pump System offers various configurations.
Centrifugal Pumps

Pump System offers various configurations.

2000 HS System, designed for transferring dewatered sludge in municipal wastewater treatment, features integral hopper with twin-screw auger feeder and Model 2000 G4 progressing cavity pump for handling semi-dry, high solids content material. Feeder supplies constant pressurized feed rate to pump resulting in 100% pump cavity fill rate. Configurations include: C-Flow, S-Flow, T-Flow, U-Flow, and...

Read More »
Variable Speed Drive controls 2 to 4 pump systems.
Centrifugal Pumps

Variable Speed Drive controls 2 to 4 pump systems.

PumpSmart Model PS 200 microprocessor based, variable speed drive is programmed specifically for centrifugal pumps up to 700 HP. Control of process parameters is obtained by continuous monitoring and reaction to both pump conditions and system demands. Pump output is matched to exact flow and head required by process. PS 200 protects pump from dry running, low suction, cavitation, dead heading...

Read More »

All Topics