Calibrators

Calibrators

Hand-held Programmer reads and writes TEDS data to smart sensors.

Model 36004 rechargeable programmer can read and write sensor location data pertaining to Smart ISOTRON or other integral electronic piezoelectric type transducers using IEEE-P1451.4 Transducer Electronic Data Sheet (TEDS) format. Device allows user to program TEDS sensor application-specific information in large, multi-channel dynamic test systems. Up to 8 characters are entered to identify...

Read More »
Force and Weight Calibrator is pocket-sized.
Calibrators

Force and Weight Calibrator is pocket-sized.

Model 125 supplies mV/V level signals for testing, calibrating, and troubleshooting load cell/scale indicators in any environment. Concise output references for 0, 1, 2, or 3 mV/V are achieved by using metal film resistor network, discrete wire wound resistors, and 2-pole 4-position rotary switch. 350 ohm input and output impedance matches typical strain gage devices. 4 permanent binding posts...

Read More »
Pressure Calibrator has dust- and splash-resistant case.
Calibrators

Pressure Calibrator has dust- and splash-resistant case.

Model 717 100G handheld, pressure calibrator measures pressure to 100 PSIG/690 kPa. It is suitable for gage, differential, absolute, vacuum, and compound applications from one inch of water to 10,000 psi. Model 717 100G measures pressure with 0.05% accuracy through its internal 100 PSIG sensor. It is equipped with 1/8 NPT pressure fitting, and is compatible with non-corrosive gases and liquids.

Read More »
RTD Calibrator measures and simulates signals.
Calibrators

RTD Calibrator measures and simulates signals.

Programmable CAL20 can calibrate electronic process equipment such as controllers, transmitters and recorders. Programmable functions include automatic output value changing, ramp/step increment value, selectable engineering units and isolated signal conversion. All calibration values can be stored and recalled using Low, Mid and High keys. It has 500 Vdc I/O isolation, reverse polarity...

Read More »
Gaging Software aids in calibration productivity.
Calibrators

Gaging Software aids in calibration productivity.

Windows NT-based software for models 828 CiM and PC length measurement systems improves measurement efficiency and manages verification process for unlimited number of gages. Software lets technicians check gage and record results in database quickly. It has user-friendly operator interface, library of ANSI standards for measuring every type of gage, and automatic recall of measurement setup and...

Read More »
Portable Blackbody certifies infrared thermometers.
Calibrators

Portable Blackbody certifies infrared thermometers.

Model 9133 is factory calibrated and NIST traceable to be accurate to ±0.7°F, has heating and cooling times of about 15 min., and certifies IR thermometers over temperature ranges from -22° F to 302° F. It has 2.25 in. temperature controlled blackbody target with emmissivity of 0.95. Target accuracies of ±0.075°C can be achieved by using contact well, located...

Read More »
Calibrators

Calibrator features multitude of programmable functions.

Model CAL30 Process Calibrator, designed to independently measure and generate dc voltage, mV and current, is able to calibrate electronic process equipment such as controllers, transmitters and recorders. Programmable functions include square-root extraction, ramp/step increment value, selectable engineering units and isolated signal conversion. Unit features NIST certification, 500 Vdc...

Read More »
Loop Calibrator can be operated with one hand.
Calibrators

Loop Calibrator can be operated with one hand.

Portable Model 707 can source, measure and simulate loop current with 0.015% accuracy and 1 Â-µA resolution. A 24 V loop supply enables user to power and read transmitter at the same time. Selectable slow ramp, fast ramp and step functions provide user with test signals needed for valve slewing and loop functional tests, allowing single technician to troubleshoot entire loop. Compact and...

Read More »
Cal-Gas Standards Generator calibrates gas analyzers.
Calibrators

Cal-Gas Standards Generator calibrates gas analyzers.

Model 491MB Gas Standards Generator is designed to calibrate gas analyzers such as gas chromatographs, mass spectrometers, and ion mobility spectrometers. 491MB uses Trace Source(TM) Permeation Tubes to generate low concentrations (1000 ppm to ppb) gas standards for VOCs, Acid Gases, Amines, Sulfurs, and Hydrocarbons (400+ compounds). Standards are traceable to NIST.

Read More »
Calibrator for pressure, temperature and electrical.
Calibrators

Calibrator for pressure, temperature and electrical.

Portable MC3 Series is available with pressure in three ranges up to 2,400 psi and optional barometric reference. Electrical section offers V, mA, Hz measurement, pulse counting, mA generation, switch testing and 24 Vdc loop supply. Temperature section has t/c, RTD, Ohm and mV measurement and generation, and V, mA, Hz and pulse generation. Calibrator is available in three configurations with...

Read More »

All Topics

COVID-19 Response Suppliers COVID-19 Response:
Can Your Company Help Provide Critical Supplies?

We are using the power of our platform to aid in the mass shortage of critical supplies. If your company can help provide supplies, capabilities, or materials for products such as N-95 Masks and Tyvek SuitsPlease let us know.

COVID-19 Response Suppliers