Digital Power Controller speeds product development.
Power, control, and data interfaces of MultiDriver(TM) Board provide integrated system for digital controller development. Switching power stage accepts 12-48V supplies and provides 6 A half-bridge or 3 A full-bridge output current. FlexController(TM) SOC allows verification of control algorithms through PC with FTview(TM) software. Data communication is through FlexBus(TM) isolated multi-drop...
Read More »
Analog Input Card offers 30 MS/s sampling rate.
High-speed, Model PCI-1714 streams continuous data from analog samples to host memory. Simultaneous sampling is provided on all 4 input channels through dedicated A/D converters. Trigger modes include software triggering, internal and external pacer triggering, post trigger acquisition, delay trigger acquisition, and pre-trigger acquisition. Card includes software for auto calibration, so no...
Read More »
Data Acquisition Module suits industrial applications.
PCM-ADIO single board, PC/104 data acquisition module combines 32-channel, 16-bit A/D converter; 4-channel, 12-bit D/A converter; 16 lines of digital I/O; and event trigger control. Onboard microprocessor controls input and configurations, conversion rates, FIFO depth, output ranges, calibration, and digital I/O settings without use of jumpers or potentiometers. Automatic conversion rate is...
Read More »
PCI Boards simplify general-purpose data acquisition.
Complete with 256-position A/D channel/gain queue, Models RCP 1612 and 3212 store up to 2,048 samples in on-board FIFO buffers. Three 8-bit digital I/O ports can be configured as inputs or outputs, and support hardware handshaking, strobe I/O, and bi-directional protocols. Each board includes six 16-bit counter/timers. Two are used internally; 4 are available to measure frequency, count events,...
Read More »
Checklist: How to Get the Right Belt the First Time
This guide is intended to help identify and address application criteria necessary to specify the right belt to deliver a highly efficient, reliable product.
Read More »
Single Board Computer suits space-restrained applications.
QCard expandable embedded controller consists of 2 x 2.5 in. SBC that incorporates up to 1 MB of memory, communications capabilities, and expansion I/O bus. Powered by 16 MHz Motorola 68HC11F1 microprocessor, controller also features 512K Flash, and 128-512 K RAM, and 320 bytes EEPROM. On-board I/O includes 8 digital I/O lines with counter/timer capabilities, 8 analog inputs, synchronous SPI...
Read More »
Digitizers integrate pre- and post-trigger capability.
Dual-channel Models ATS1250 and ATS1220 are 12-bit PCI waveform digitizers for ultrasonic imaging and inspection, shock and vibration, and scientific applications. ADC and ASoPC technologies provide 60 dB signal-to-noise ratio. Units provide independently programmable inputs from Ã-
Read More »
Communication Module provides 8 RS-232/422/485 ports.
MultiComm(TM) serial controller module delivers 8 independent asynchronous serial channels, 10 Mbps Ethernet, and 2 CAN ports for embedded PC/104 computer systems running WindowsÃ-®, LinuxÃ-®, and real-time operating systems. Serial ports, 16C550C-compatible, operate at up to 921.6 kbps and are configured in pairs as 8 RS-232 or 4 RS-232 and 4 RS-422/485 ports capable of controlling up to...
Read More »
PC-104 Board features optically isolated I/O.
Model 104-IDIO-16 is a 32-channel PC-104 utility board featuring 16 optically isolated input and 16 optically isolated solid-state outputs. Non-polarized inputs may be driven by dc sources of 3-31 V or ac sources at frequencies of 40 Hz to 10 KHz. Models are available with or without input change-of-state detection. Input channels have 34-pin IDC-type header. Outputs drive up to 1 A each and are...
Read More »
I/O Boards combine digital I/O and counter/timers.
Multi-function I/O boards, Model APC424/464 for desktop PCI and Model AcPC424/464 for CompactPCI, each replace 2 I/O boards to conserve card slots. The 424 models provide 40 digital I/O channels for TTL and differential signals plus four 16-bit counter/timers, while 464 models have 64 TTL digital I/O and 4 counter/timers. Digital I/O channels are bi-directional to meet almost any input/output...
Read More »
Starter Kit facilitates embedded system development.
Embedded System Module Starter Kit features ESM mezzanine card, universal ESM carrier card for power and I/O interfaces, and all cables and linking connectors needed to start development. Kit can be ordered with ESM based on Motorola PowerPC or one of several Intel x86 processors. Module includes memory, system I/O, and I/O connectors. Carrier card on which ESM is mounted provides additional I/O,...
Read More »
Standex Engraving Mold-Tech Offers Nickel Shell Capabilities on a Global Scale
Standex Engraving Mold-Tech is the premier, global supplier for mold texturing and surface finishing. With a full range of services, Standex Engraving Mold-Tech is also the only nickel shell supplier producing in three global locations. See our video to learn more.
Read More »
