Arc / Resistance Welders

Multi-MIG Welding Inverters monitor arc conditions.
Arc / Resistance Welders

Multi-MIG Welding Inverters monitor arc conditions.

Software-driven, Axcess(TM) 675 provides output of 675 A/44 V at 100% duty cycle, making it suited for large welds requiring long cycle times. Voltage range in CV mode is 10-44 V with 80 Vdc max open circuit voltage. Auto-Line technology enables machine to accept any primary power from 190-630 V, single- or 3-phase, 50 or 60 Hz. Auto-Axcess 675 offers same features but communicates through...

Read More »
AC/DC TIG Welder delivers 200 A of welding power.
Arc / Resistance Welders

AC/DC TIG Welder delivers 200 A of welding power.

Pulling 25 A of power, Invertig 201 AC/DC TIG Welder allows users to vary AC frequency from 20-200 Hz while maintaining square wave throughout complete range for control over arc. Pulsing, with frequency from 0.4-300 Hz, is standard, and balance is adjustable from 10-90%. Unit weighs 65 lb and fits in cabinet measuring 20 x 9Â-½ x 19¾ in. It comes with 25 ft SR-17 air-cooled TIG...

Read More »
Arc / Resistance Welders

TIG Welding Machine comes with pulser.

With operating range from 5-185 A, Precision(TM) TIG 185 utilizes Micro-Start(TM) Technology for stable arc starting and crater control. Auto-Balance(TM) with manual override optimizes ratio of cleaning action vs. penetration, while pulse system controls heat input and features visual pulsing light to aid in setting rate. Machine has top-mounted torch parts storage compartment; detachable,...

Read More »
Arc / Resistance Welders

Welding System includes a generator and air compressor.

Air Vantage® 500 employs direct gear-driven compressor with no belts or clutches, rated at 60 cfm, 100 psi at 100% duty cycle. Unit comes with up to 20,000 W of 3-phase 240 Vac generator power and can provide 12,000 W continuous 1-phase AC generator power. Features include Chopper Technology; Touch-Start(TM) TIG; stainless steel roof, side panels, and sliding engine-access door; as well as...

Read More »
Orbital Weld Heads weld pipe in place.
Arc / Resistance Welders

Orbital Weld Heads weld pipe in place.

Redhead weld heads, used with digital Tubemaster Power Source, are designed for orbital welding of pipe/tubes from 0.5-6.625 in. Products can be used for autogenous welding applications or with optional wire feeder. Mechanical device maintains constant arc length on out-of-round pipes, and design incorporates continuously adjustable clamping. Weld heads mount on one side of weld joint, allowing...

Read More »
Arc / Resistance Welders

Welder/Generator incorporates Kohler LPG engine.

Multi-process Ranger(TM) 250, powered by low-emission liquid propane gas, utilizes Chopper Technology(TM), which provides smooth arc and low spatter. It delivers 250 A for welding at 100% duty cycle and 9,000 peak W of 120 V/240 AC generator power. Welder features downhill pipe welding mode, arc control adjustment, and touch-start TIG mode. Its 20 hp Command® LPG OHV engine features...

Read More »
Welder/Power Generator provides 10,000 W peak power.
Arc / Resistance Welders

Welder/Power Generator provides 10,000 W peak power.

Ranger(TM) 10,000 allows operators to simultaneously weld and use AC generator power. At 100% duty cycle, machine is rated 225 A for AC Stick welding, 210 A for DC Stick welding, and 200 A for CV wire welding. Full KVA 120/240 V outlet allows operators to run high-capacity motors, while four 120 V outlets provide auxiliary power. Unit is available with Kohler® or Honda® 2-cylinder,...

Read More »
Stick/TIG Inverter offers 5-150 A welding range.
Arc / Resistance Welders

Stick/TIG Inverter offers 5-150 A welding range.

Maxstar® 150 Series includes Stick only, Stick/TIG Lift-Arc start, and Stick/TIG high frequency or Lift-Arc start models. All have Stick output of 150 A at 30% duty cycle, enabling nearly unlimited welding with 1/8 in. diameter Stick electrode. Auto-Line feature allows units to connect to 115-230 Vac single-phase power, ± 10%, and maintains steady arc if primary power varies. Fast...

Read More »
Pedestal-Style Welder features flexible, compact design.
Arc / Resistance Welders

Pedestal-Style Welder features flexible, compact design.

Series INV welder can be used as freestanding machine or incorporated into automated welding cells. It can be supplied with up to 5 in. cylinder that produces approximately 1,600 lb of weld force or 2 in. cylinder that produces 60 lb of force. Welder can be furnished with ac transformers, ranging from 7Â-½ to 50 KVA, or dc inverter power supplies for up to 140 KVA. It has 8 in. throat depth...

Read More »

All Topics

COVID-19 Response Suppliers COVID-19 Response:
Can Your Company Help Provide Critical Supplies?

We are using the power of our platform to aid in the mass shortage of critical supplies. If your company can help provide supplies, capabilities, or materials for products such as N-95 Masks and Tyvek SuitsPlease let us know.

COVID-19 Response Suppliers