Adhesives

Encapsulants

Adhesive cures with ultra violet light or heat.

OPTOCAST AC-3716 100% solids, low viscosity, 1-component, acrylate-based formulation can be cured almost instantly with exposure to ultra violet light in 320-380 nm wavelength range or with heat to cure shadowed areas. It cures to soft, compliant material with Shore A hardness of 60-62. OPTOCAST AC-3716 exhibits excellent adhesion to variety of metal, ceramic, and glass-filled epoxy surfaces.

Read More »
Fillers

Gap Fillers offer range of conductivity, compression rates.

Available in 24 x 24 in. sheets, ThermaCool® TC2006/TC3006/TC3008 soft and compliant gap fillers can accommodate materials of varying coefficients of thermal expansion. Compression force enables them to span multiple components with minimal pressure, and thermal conductivity optimizes heat transfer. Intrinsically tacky, products require no adhesive and can also be ordered with fabric or...

Read More »
Coating Equipment

Dow Corning Showcases Syl-Off® Advantage Series at Labelexpo

MIDLAND, MICHIGAN, USA: Dow Corning Corporation will showcase its proven Syl-Off® Advantage Series, an extensive line of low-platinum, solventless release coating products, at Labelexpo Americas 2008, Booth 3511. The Advantage Series provides many choices for customers to meet their needs. Today more than 80 coaters in 25 countries utilize the Advantage Series, which provides excellent...

Read More »
Epoxy Adhesive bonds sensors to CNC machine tools.
Epoxies

Epoxy Adhesive bonds sensors to CNC machine tools.

Suited for aerospace manufacturers, ASTM E-595 compliant Aremco-Bond(TM) 631 two part, modified epoxy has tensile shear strength of 3,000 psi as measured by ASTM D1002-94, volume resistivity and dielectric strength of 1.2 x 1,014 Wcm and 440 V/mil respectively, and maximum operating temperature of 204Â-ºC. It features total mass loss of 0.75% at 125ºC, and collected volatile...

Read More »
Transfer Adhesive bonds to range of foam substrates.
Adhesives

Transfer Adhesive bonds to range of foam substrates.

Measuring 4 mils thick with adhesive thickness of 3.75 mils, Type 7434-74 includes 74 lb liner that can be removed after lamination to fragile low density foams without foam tearing. Aggressive, acrylic-based transfer adhesive offers elevated temperature performance and is suited for bonding to broad spectrum of foam substrates including ether, ester low perm urethane, and melamine foams.

Read More »
Applicators

Ellsworth Adhesives to Showcase Key Suppliers' Technologies at Assembly Technology Expo 2008

Germantown, WI - Ellsworth Adhesives, a leading global provider of adhesives, specialty chemicals and engineered solutions will exhibit technologies from leading suppliers at the 2008 Advanced Technologies Expo, September 23-25, 10 a.m. - 4 p.m., daily at the Donald E. Stephens Convention Center in Rosemont, IL, booth 444. This event offers attendees an outstanding opportunity to keep pace with...

Read More »
Adhesives bond to plastics and other substrates.
Adhesives

Adhesives bond to plastics and other substrates.

Compatible with BlueWave® LED high-intensity spot curing system, DYMAX 3000 Series cures in seconds upon exposure to UV light and/or visible light. No-VOC adhesives form environmentally resistant bonds to plastics and other substrates including polycarbonate, PVC, phenolic, acrylic, metal, glass, and ceramic. BlueWave® curing system emits maximum visible light intensity output of over...

Read More »
Sprayable Mastic targets joints where movement is required.
Mastics

Sprayable Mastic targets joints where movement is required.

For firestopping top of wall, expansion, and edge of slab/curtain wall joints, CP 672 Fast Cure Speed Spray is paintable and designed for use with concrete floor assemblies. Applicable by spray or brush, water-based mastic makes spills and over-spray quick to clean up. Containing no halogens, solvents, or asbestos, spray meets LEED requirements for indoor environmental quality. Product can be...

Read More »
Adhesives

Flame Retardant Adhesive has V0 flammability rating.

Meeting ASTM standard D3801 flammability specification, electrically isolating F2591 adheres to silicon, ceramic, aluminum, and copper substrates. RoHS-compliant product is stable at room temperature for 1 month and can be stored at 0°C for 3 months or -40°C for 1 year. Available in sheet or roll format up to 18 in., adhesive can be provided as film or preform in thicknesses from...

Read More »
Miscellaneous Paper

Rayven, Inc. to Showcase Depth of Products at Label Expo Americas

Diverse Product Offering Perfect for Projects that Go the Extra Mile ST. PAUL, MN - Rayven Inc., a leading provider of laminating, coating and converting services, is proud to announce its diverse lines of release liners and coated products will be on exhibit at Label Expo Americas. The lineup of products to be showcased will include: o A new 48 gauge (ultra-slim) PET release liner. This narrow...

Read More »

All Topics

COVID-19 Response Suppliers COVID-19 Response:
Can Your Company Help Provide Critical Supplies?

We are using the power of our platform to aid in the mass shortage of critical supplies. If your company can help provide supplies, capabilities, or materials for products such as N-95 Masks and Tyvek SuitsPlease let us know.

COVID-19 Response Suppliers