Encapsulant/Potting Material exhibits
Repair Compounds

Encapsulant/Potting Material exhibits

Ceramacast(TM) 510 aluminum oxide based, hydraulic-setting ceramic compound potting material can be used to encapsulate cartridge heaters and embed high temperature components to 3200Â-ºF. Supplied as dry powder, Ceramacast 510 is bonded using calcium aluminate and as-cast. Its dried density is 180 lbs/ft3, and it exhibits exceptional thermal conductivity and dielectric strength of 75-100...

Read More »
Epoxy Adhesive fixes electrical coils.
Epoxies

Epoxy Adhesive fixes electrical coils.

Tra-Bond CA20 thixotropic epoxy adhesive system is formulated for shorted turns, damaged end wire extensions, or other coil repair applications where high-fill, non-sag adhesive is needed. It provides high dielectric isolation and good mechanical strength. Readily mixed, handled, used, and cured at room temperature, Tra-Bond CA20 develops strong bonds to materials such as metals, glass, ceramics,...

Read More »
Case Sealer suits demanding applications.
Sealing Equipment

Case Sealer suits demanding applications.

OK Supertaper 1M seals both tops and bottoms of cases with tape. Standard features include stainless steel exterior finish and heavy-duty side belts with 1/4 hp motors that can handle cases up to 90 lbs. Four in. wide side belts handle heavy and bulging cases. OK Supertaper 1M features OK55 tape heads with open tape feed path.

Read More »
Adhesive Tapes

Gasket Tape protects fragile equipment.

Made from 100% multidirectionally expanded PTFE, GORE-TEX Series 600 gasket tape seals large-diameter fragile and glass-lined equipment. It is resistant to all chemicals, tolerates temperatures from -450 to +600°F, and is available in 5 widths and thicknesses of 1/4 and 3/8 in. Tape maintains original width when compressed, ensuring high gasket stress retention, dimensional stability, and...

Read More »
Case Sealer can convert to 2 in. or 3 in. tape requirements.
Sealing Equipment

Case Sealer can convert to 2 in. or 3 in. tape requirements.

Little David Random Legend Series Case Sealer uses pressure sensitive tape to seal top and bottom of boxes. It tapes boxes ranging from 3 to 24 in. high, 4 1/2 to 22 in. wide, and from 3 in. in length. Side and lock leg extensions accommodate conveyor heights from 22 1/4 to 32 1/4 in. Sealed drive system and CaseLocker ST cartridge require no lubrication. Sealer features single mast design with...

Read More »
Bag Sealer provides continuous performance.
Sealing Equipment

Bag Sealer provides continuous performance.

OK Supersealer heat sealer utilizes hot air to continuously seal wide range of bag materials at high speed. It does not use Teflon® coated bands, which decreases downtime. System offers integral heater height measurement, variable speed, auto-reverse function, stainless steel finish, and PLC controller.

Read More »
Adhesive Tapes

Adhesive Transfer Films perform well on foam substrates.

4-mil Unifilm U618A and 5-mil Unifilm U619A high-performance acrylic adhesive transfer films offer extremely high tack, and are designed to provide high initial wet out and superior anchorage to ether and ester foams. Transfer films perform well over range of operating temperatures, and offer very high peel strength. Products deliver humidity and water resistance, and may be die-cut.

Read More »
Epoxies

Adhesive Epoxies come in pre-formulated cartridges.

Epox-Eez(TM) twin pack cartridges are pre-filled, measured and mixed. Adhesive will cure at room temperature, provide 500°F service, and have chemical, electrical and moisture resistance. Epox-Eez cartridges are available for company's General Purpose 4525N, Low Viscosity 4461N, Vibration Resistant 4535N, Fast Set 4537N, Ultra Flexible 4538N, and Machinable Epoxy 4540N high-temperature...

Read More »
Epoxies

Epoxy Board is designed for use at temperatures to 250°F.

Ren Shape 5008 epoxy board can be machined with carbide cutters to generate molds with good edge definition, dimensional stability, and smooth surface finish. It can be used to produce intermediate-temperature models, heat-resistant thermoform tooling, and lay-up tools for composite parts. Molds may be produced for thermoforming detailed, production-quality parts from polypropylene, polystyrene,...

Read More »
Epoxy Casting Compound meets UL fire retardant specs.
Epoxies

Epoxy Casting Compound meets UL fire retardant specs.

TRA-CAST 3143 has low viscosity, long pot life, and is certified to UL 94 V-O. Epoxy system has low coefficient of thermal expansion and excellent wetting and adhesion to most electronic and aerospace-industry materials, including metals, glass products, ceramics, industrial laminates and many rigid plastics. Applications include rigid potting, laminating, transformer encapsulating, filament...

Read More »

All Topics

COVID-19 Response Suppliers COVID-19 Response:
Can Your Company Help Provide Critical Supplies?

We are using the power of our platform to aid in the mass shortage of critical supplies. If your company can help provide supplies, capabilities, or materials for products such as N-95 Masks and Tyvek SuitsPlease let us know.

COVID-19 Response Suppliers