New Cushion Grip Denture Adhesive is Zinc-Free and Non-Toxic
The Cushion Grip™ Thermoplastic Denture Adhesive is offered in 1 oz tube and is manufactured from thermoplastic polymers that are heat activated and 100% waterproof. The product on one application can hold dentures for up to 4 days.
Read More »New TPE Compound Grades from Colorite are Durable
Colorite is adding 12 new grades to its Cellene® thermoplastic elastomer (TPE) compounds. The line previously had 28 grades and was used in healthcare and medical device manufacturing. The compounds are available in four series: 1,000 (extrusion grades for IV therapy with high clarity, improved bonding and kink resistance); 2,000 (injection molding and extrusion grades targeting cost-driven IV...
Read More »
Master Bond Launches EP3UF-1 Underfill Epoxy with Dielectric Constant of 4.5
The EP3UF-1 Thermally Conductive Underfill Epoxy is offered in 10 cc syringes and 30 cc syringes. The product features viscosity of 5,000-15,000 cps, compressive strength of 18,000-20,000 psi and tensile modulus of 450,000-500,000 psi. The compound exhibits thermal conductivity and resistance of 1.30-1.44 W/(m•K) and 5-7 x 10-6 K•m²/W respectively. The epoxy cures in 20-30 minutes at 250°F,...
Read More »
Master Bond Offers MasterSil 980 Fluorosilicone with a Dielectric Constant of 6.4
The MasterSil 980 Two Part Fluorosilicone is suitable for high performance bonding, sealing, coating and potting applications. The product features an elongation of 100-200% at 75°F and provides an operating temperature of -85°F to +465°F. The adhesive bonds with metals, composites, ceramics, glass, rubbers, plastics and silicones and has a volume resistivity of more than 10^14 ohm-cm. It can...
Read More »
A Kickstart Guide to Cyanoacrylates
This eBook provides a guide to Cyanoacrylate instant adhesives.
Read More »
New Vinyl Hybrid Resin from Perma-Liner is Formulated with Zero Styrene
The Vinyl Hybrid Resin is resistant to sag and draining around vertical surfaces and reinforcement. The product features pot life of more than eight hours and allows hot water or cool water to be cured at minimum temperature of 140°F held for 28 minutes. It can be used in areas such as schools, hospitals, churches and office buildings. The vinyl hybrid resin features a high-rigid polymer...
Read More »
Creative Materials Introduces 127-30HV Silicone Adhesive for Coating, Printing, Fastening and Bonding Applications
Creative Materials has introduced the new 127-30HV silicone adhesive. It is a flexible, re-workable, electrically conductive silicone-based adhesive, ink, and coating. It balances adhesion, cohesion, printability and high-temperature performance for coating, printing, fastening and bonding applications. 127-30HV is suitable for high reliability interconnects stretchable conductive features,...
Read More »PES Increasingly Preferred for Hollow-Fiber & Cast-Membrane Filter Media
Engineering thermoplastic provides superior properties for fluid handling in applications ranging from dialysis equipment to water-treatment filters Phoenix, Ariz., U.S. — The engineering thermoplastic polyethersulfone (PES) is increasingly the choice to produce hollow fibers for fluid transport and cast membranes for filtration applications thanks to its high mechanical, chemical, and thermal...
Read More »
New EP17HTND-CCM Epoxy Exhibits a Thermal Conductivity of 1.4423 W/(m.K) at 75 Degrees F
Master Bond’s EP17HTND-CCM Single Component Epoxy features a resistivity of more than 10^15 ohm-cm at 75°F and over 10^12 ohm-cm at 400°F. The compound can be used in -80°F to +600°F temperature and forms high strength bonds to substrates such as metals, ceramics, plastics, composites and circuit board materials. The material is offered in syringes with sizes ranging from 10 cc to 30 cc and...
Read More »
Permatex Offers ScrewGlue Repair Gel That Uses Non-Drip Clinging Formula
The ScrewGlue Repair Gel is used for fixing damaged and stripped screws and threaded holes in household items. The clinging formula of the gel makes it suitable for use overhead and hard-to-reach places. The gel helps in preventing screws and bolts from future loosening caused due to vibration, frequent use, thread corrosion and exposure to the elements. The product is used for repairing cabinet...
Read More »
New Henkel Underfill Operates at High Temperatures For use in Aero and Auto Electronics
Henkel's new under-fill Loctite Eccobond UF 1173 operates at high temperatures of 155 degrees C. Applications include use in driver assistance systems with products such as cameras, and radars in both the automotive and aerospace industries.
Read More »
Increase Workplace Safety, Manage Heavy Loads with Equipment from A-Plus Warehouse
A-Plus Warehouse carries a wide selection of commercial and industrial material handling equipment at affordable prices. Check out the video to learn more.
Read More »
