PVE-EX Electrohydraulic Actuators feature cast iron enclosure.
Meeting ATEX and IECEx standards, PVE-EX Electrohydraulic Actuators is suitable for in underground mining applications and oil and gas markets. These units use spool position feedback control signal for closing PVG valve main spool position. Units are designed with built-in safeguards and uses flame-proof protection method
Read More »
PVE-EX Electrohydraulic Actuators feature cast iron enclosure.
Meeting ATEX and IECEx standards, PVE-EX Electrohydraulic Actuators is suitable for in underground mining applications and oil and gas markets. These units use spool position feedback control signal for closing PVG valve main spool position. Units are designed with built-in safeguards and uses flame-proof protection method
Read More »
Proportional Valve Electrical Actuators feature built-in safeguards.
Proportional Valve Electrical Series 7 Actuators (PVE S7) come with microcontroller with embedded software algorithms. Operating in -40 to +90 °C temperature range, units use spool position feedback signal for closing the loop on PVG/Steering valve main spool position. Actuators are designed with fault monitoring, spool position sensor with dual demodulator. Units are enabled by LED lights for...
Read More »
Proportional Valve Electrical Actuators feature built-in safeguards.
Proportional Valve Electrical Series 7 Actuators (PVE S7) come with microcontroller with embedded software algorithms. Operating in -40 to +90 °C temperature range, units use spool position feedback signal for closing the loop on PVG/Steering valve main spool position. Actuators are designed with fault monitoring, spool position sensor with dual demodulator. Units are enabled by LED lights for...
Read More »
PCB Fabrication Notes Guide
The overall purpose of your fabrication notes is to enhance Design for Manufacturability for optimal PCB fabrication and assembly while maintaining applicable industry standards and regulations.
Read More »Programmable Electric Actuators Rapidly Replacing LVDT's, Ball Screws in Pin Insertion and Height Gauging
CARLSBAD, CALIFORNIA - Programmable electric actuators have been increasingly favored as airless substitutes for LVDT’s and ball screws in connector pin insertion and connector pin height measurement. Unlike ball screws or LVDT’s, electric actuators have programmable positioning. They can press the pin in with the correct force, verify its position, and provide a tight fit every time. This...
Read More »Programmable Electric Actuators Rapidly Replacing LVDTâ™s, Ball Screws in Pin Insertion and Height Gauging
CARLSBAD, CALIFORNIA - Programmable electric actuators have been increasingly favored as airless substitutes for LVDT’s and ball screws in connector pin insertion and connector pin height measurement. Unlike ball screws or LVDT’s, electric actuators have programmable positioning. They can press the pin in with the correct force, verify its position, and provide a tight fit every time. This...
Read More »
DYNAMIXEL X-Series Actuators feature redesigned aluminum case.
DYNAMIXEL X-Series Actuators offer idle current of 40mA and can track output position up to 4096 steps-per-revolution. Units use hollow back case which allows user to rout wires under the rear cable cover or via a port-hole in the idler bearing. Product enables operator to modify acceleration and velocity parameters and provides two current-based torque control modes. Actuators feature 360-degree...
Read More »
DYNAMIXEL X-Series Actuators feature redesigned aluminum case.
DYNAMIXEL X-Series Actuators offer idle current of 40mA and can track output position up to 4096 steps-per-revolution. Units use hollow back case which allows user to rout wires under the rear cable cover or via a port-hole in the idler bearing. Product enables operator to modify acceleration and velocity parameters and provides two current-based torque control modes. Actuators feature 360-degree...
Read More »
Motion Slide Actuators are suitable for X-Y and X-Y-Z positioning systems.
Motion Slide Actuators are available in Gen 2 compact and value line linear motor-ready models. Units come with horizontal, vertical, or inverted mounting options and integral sensor mount grooves. Compact slide actuators offer travel distance to 36 in. and travel speeds up to 20 in. per second and comes with a motor mount which is compatible with NEMA 17 and 23 motors. Value line linear slide...
Read More »
Motion Slide Actuators are suitable for X-Y and X-Y-Z positioning systems.
Motion Slide Actuators are available in Gen 2 compact and value line linear motor-ready models. Units come with horizontal, vertical, or inverted mounting options and integral sensor mount grooves. Compact slide actuators offer travel distance to 36 in. and travel speeds up to 20 in. per second and comes with a motor mount which is compatible with NEMA 17 and 23 motors. Value line linear slide...
Read More »
Dodge® Raptor Coupling Now Available in Three Larger Sizes
The Dodge Raptor coupling epitomizes the innovation and value that has made Baldor a world leader in industrial electric motors. For almost 100 years Baldor has been the go-to source for industries across the globe. The Raptor coupling is just one example of our dedication to engineered excellence and commitment to providing value and performance. See our video to learn more.
Read More »
