Accelerometer provides underwater vibration measurements.
Chatsworth, CA (December 3, 2007) - Dytran Instruments, Inc. is pleased to announce the availability of the new low profile accelerometer designed specifically for underwater vibration measurements. It features a center bolt mount with 360-° cable orientation. This unit can be used down to depths where the water pressure reaches 175 psi. The 3211M1 is 10mV/g and features an integral 10 foot...
Read More »Endevco Corporation, the leader in sensing solutions for demanding vibration, shock and pressure applications, has announced introduction of the Endevco model 65HT-05 triaxial, high-temperature accelerometer. The model 65HT-05 expands on the model 65HT family of products designed for automotive test cells, environmental and aerospace test chambers, and general laboratory applications where high...
Read More »Differential Accelerometer suits high-temperature jobs.
Dytran Instruments, Inc. of Chatsworth, CA has developed a new high temperature differential accelerometer. The 3085C can operate at temperatures up to +600-°F and is ideal for turbine engine vibration measurements, as well as other high temperature applications. This 10pC/g charge mode accelerometer features a favorable 3-bolt pattern mounting flange and a 2-pin electrical connector. Other...
Read More »
Miniature Accelerometer performs shock and vibration studies.
October 5, 2007, Depew, NY, USA - PCB Piezotronics (PCB-®) has introduced Model 357A19, a very miniature charge output accelerometer, designed for performing shock and vibration studies in space-restricted locations and on small, lightweight structures. The unit occupies a 0.11 x 0.16 x 0.27 inch (2.8 x 4.1 x 6.9 mm) envelope, and weighs a mere 0.007 ounces (0.20 grams), for minimal mass loading...
Read More »
Advantages of VPSA Technology for Your Application
VPSA technology uses different equipment than PSA and requires significantly less energy, resulting in an average cost savings of one-third to one-half in comparison to PSA systems.
Read More »
Industrial Accelerometer operates to 30k Hz.
Working with online or portable monitoring systems to provide vibration monitoring, Model 621B40 captures high-frequency gear mesh faults often missed during routine route-based measurements. Magnetically mounted unit supplies response to more than 30k Hz, allowing vibration analyst to obtain precise measurements of high frequency phenomena. Device is suited for measurements on high-speed...
Read More »Endevco to Display State-of-the-Art Sensor Technology at Automotive Testing Expo 2007 China
Endevco Corporation, the leader for 60 years in sensing solutions for demanding vibration, shock and pressure applications, will showcase a wide range of its most popular products for crash test, pressure, and noise, vibration and harshness applications in booth #6064 at the Automotive Testing Expo 2007 China to be held September 12-14, 2007 at the Shanghai Everbright Convention and Exhibit...
Read More »Motion Sensors are suited for low-g applications.
CEATEC 2007, October 2, 2007 - STMicroelectronics (NYSE: STM), one of the world's leading manufacturers of MEMS (Micro Electro-Mechanical System) devices, today introduced a new generation of 'nano' three-axis linear accelerometers. The versatile, low-power MEMS sensors provide complete output flexibility and embedded smart features, meeting the exploding demand for miniaturized motion-sensing...
Read More »Linear Accelerometers target portable electronic devices.
GENEVA, Oct. 2 /- STMicroelectronics (NYSE:STM), one of the world's leading manufacturers of MEMS (Micro Electro-Mechanical System) devices, today introduced a new generation of 'nano' three-axis linear accelerometers. The versatile, low-power MEMS sensors provide complete output flexibility and embedded smart features, meeting the exploding demand for miniaturized motion-sensing solutions in the...
Read More »
IMI Sensors Series 660 Low-Cost Embeddable Sensors ....
September 13, 2007, Depew, NY, USA - Series 660 low-cost embeddable accelerometers from the IMI Sensors division of PCB Piezotronics (PCBÃ-®) are ideal for continuous shock and vibration monitoring in high volume and commercial OEM applications. They offer high shock survivability, high resolution and large dynamic range. Units employ field-proven, solid-state piezoelectric sensing elements...
Read More »
ESS Accelerometer suits small size/low mass applications.
Model 3089A subminiature, adhesive mount accelerometer features 10 mV/g sensitivity. Weighing 0.6 g, it includes integral lead wires and can be used for Environmental Stress Screening (ESS), printed circuit board testing, and OEM/embedded applications.
Read More »
How SpinSelect Can Save You Time and Money
Thanks to the unique SpinSelect™ Multi-Pocket selectable quick change tool holder, it's time to rethink the range, complexity and volume of parts that your lathe can produce. Our Spin-Select™ tool was created to increase productivity and consistency by decreasing downtime associated with lathe cutting tool and insert setups or changeovers. This product is a game-changer for the industry and we're pleased to show you why.
Read More »