Accelerometers

SCA3300 Series Accelerometers meet AEC-Q100 quality standards.
Accelerometers

SCA3300 Series Accelerometers meet AEC-Q100 quality standards.

Housed in pre-molded dual flat lead 7.6 x 8.6 x 3.3mm SMD package, SCA3300 Series 3-Axis MEMS Accelerometers are operated from 3.3 VDC supply with 1 mA consumption during normal operation. Delivering non-linearity of 0.1 % and noise density of 37 ug/√Hz, units feature an offset stability of less than 10mg. Used for levelling and alignment system and inertia measurements, accelerometers have an...

Read More »
MEMS Accelerometers offer electrostatic self-test.
Accelerometers

MEMS Accelerometers offer electrostatic self-test.

Available in ADXL1001 and ADXL1002 models, MEMS Accelerometers are operated in -40°C to +125°C temperature range with 3.0 V to 5.25 V single voltage supply. ADXL1001 model offers ±100g full scale range and noise density of 30 μg/√Hz whereas ADXL1002 model provides ±50g and 25 μg/√Hz noise density. Accelerometers are suitable for industrial condition monitoring and smart factory IoT...

Read More »
3133D Series - Miniature Accelerometer for Product Development Testing
Accelerometers

3133D Series - Miniature Accelerometer for Product Development Testing

August 11, 2016 – Chatsworth, California, USA – Dytran Instruments, Inc. (www.dytran.com) a leading manufacturer of piezoelectric and DC MEMS accelerometers, dynamic force and pressure sensors, cables, and associated electronics, is pleased to announce the release of series 3133D, ultra miniature hermetically sealed IEPE triaxial accelerometers. Today’s electronic devices continue to...

Read More »
3543A, High Sensitivity, Isolated, High Temperature IEPE Triaxial Accelerometer
Accelerometers

3543A, High Sensitivity, Isolated, High Temperature IEPE Triaxial Accelerometer

August 31, 2016 – Chatsworth, California, USA – Dytran Instruments, Inc. (www.dytran.com) a leading manufacturer of piezoelectric and DC MEMS accelerometers, force and pressure transducers and associated electronics, is pleased to announce the release of the 3543A, our first high temperature, 100mV/g, internally electrically isolated triaxial accelerometer. This accelerometer is the first...

Read More »
3493A Series IEPE Triaxial Accelerometers are housed in titanium case.
Accelerometers

3493A Series IEPE Triaxial Accelerometers are housed in titanium case.

Available in models with 5mV/g and 10mV/g sensitivities, 3493A Series IEPE Triaxial Accelerometers feature shielded cable design with 4-pin, ¼-28 threaded connector termination. Suitable for product response testing, modal and structural analysis and triaxial vibration testing applications, units measure .30 L x .24 W x .26 in. H and weighs 0.9 g. Having resonant frequency greater than 30 kHz,...

Read More »
KXTJ3 Accelerometer features built-in voltage regulator.
Accelerometers

KXTJ3 Accelerometer features built-in voltage regulator.

Used in pet monitors, smart tags, beacons and key fobs, KXTJ3 Accelerometer can operate with low 1.5uA at its lowest ODR of 0.781Hz. Offering g-ranges of 2g, 4g, 8g, or 16g and resolution modes up to 14g, unit comes in 2mm x 2mm x 0.9mm form factor. Featuring embedded motion wake-up engine with 3.9mg threshold, unit supports I2C protocol up to 3.4MHz.

Read More »
MEMS VC Accelerometers feature self calibration.
Accelerometers

MEMS VC Accelerometers feature self calibration.

Housed in one sq-in anodized epoxy sealed aluminum, Model 2210 Series Accelerometer is integrated with MEMS VC accelerometer chip and high-drive, low-impedance buffering for reliable measurements. Operated in +8 to +32 V supply voltage, product provides 0 VDC differential output voltage at ±4 VDC full scale. Unit is relatively insensitive to temperature changes. Capable of measuring with 1, 2 or...

Read More »
IMI Sensors Announces CSA Approval for Models EX611A00 and EX611A20
Accelerometers

IMI Sensors Announces CSA Approval for Models EX611A00 and EX611A20

Extreme Temperature, Charge-Mode Accelerometer Now Certified as Intrinsically-Safe in US and Canada November 23, 2016 DEPEW, NY - IMI Sensors, manufacturer of industrial vibration and pressure monitoring instrumentation, announces CSA approval on Models EX611A00 and EX611A20, two extreme temperature, charge mode accelerometers with a UHT-12™ sensing element. This approval now allows the two...

Read More »
MEMS Accelerometers help detect structural defects early.
Accelerometers

MEMS Accelerometers help detect structural defects early.

Performing high resolution vibration measurement with very low noise, 3-axis Models ADXL354 and ADXL355 enable early detection of structural defects via wireless sensor networks. Devices provide output of ±2 to ±8 g full scale range, selectable digital filtering from 1 Hz to 1 kHz, and low noise density of 25 µ/√Hz at less than 200 µA current consumption. Supplied in 6 x 6 mm...

Read More »

All Topics