Thermacore k-Core Technology Cools NASA's Earth Science Satellite Observatory
Lancaster, PA – When NASA launched its environmental research satellite on January 31, 2015, it carried sensitive Soil Moisture Active Passive (SMAP) instrumentation that utilized mission-critical cooling components from k Technology, a Division of Thermacore, Inc. (www.thermacore.com), a leading provider of advanced thermal solutions.
The SMAP mission is designed to help scientists understand the links between Earth's water, energy and carbon cycles. Functioning as an Earth observatory in space, the satellite improves the ability of weather forecasters and climate scientists to monitor and predict natural hazards, such as floods, landslides and droughts. SMAP soil moisture data are used by agricultural and water resource managers to develop water and climate models. The SMAP project is managed for NASA by the Jet Propulsion Laboratory (JPL), with participation by the Goddard Space Flight Center (GSFC). Throughout the SMAP mission, internal heat generated by the satellite’s electronics must continually be rejected into the cold and vacuum of outer space.
To meet this difficult thermal challenge while maintaining strict weight and size limits, NASA called upon Thermacore’s thermal management and engineering expertise to develop a unique heat spreader -- also known as a “doubler” -- to cool a critical electronics bus panel.
Instead of using typical aluminum heat-spreader material, the doubler utilizes k-Core® Annealed Pyrolytic Graphite (APG) encapsulated within aluminum to form a composite panel. The six-millimeter thick panel is a sandwich comprised of an aluminum exterior shell that is one-millimeter-thick on each side wrapped around a four-millimeter thick APG core. The advanced APG material enabled the large 0.7-meter long and 0.7-meter-wide panel to achieve a significant weight reduction of approximately 15 kilograms without sacrificing thermal performance.
The hard anodized plate was finished to support an array of thermal attachment points, thermally and electrically conductive areas, plus grounding areas. According to Mark Montesano, Vice President of Engineering, Thermacore k Technology Division, “The complex finishing requirements presented a challenging design. This project involved a detailed mechanical design as well as a finite element thermal analysis to determine component locations and specific geometry of the APG insert within the structure.”
The thermal/mechanical analysis identified such variables as graphite-edge distances and thru-hole features. The Thermacore k Technology team undertook a predictive-performance analysis using an iterative process with JPL to determine optimum locations and component configuration. From that point, engineering drawings were generated for all the components, which were then released to k Technology’s fabrication facility for graphite machining, composite assembly and machining, plating and inspection. The panel was then shipped to JPL for bench testing, preflight evaluation and then installation on the spacecraft for the January 2015 launch.
In addition to the advanced thermal solution for the SMAP mission, Thermacore will provide a k-Core thermal strap for the thermal clock on the JPL GRACE Follow-on Mission. Scheduled for launch in 2017, this mission will measure the change in water stored on land from precipitation that has been stored as snow, that infiltrated into the ground or evaporated, or that left the basin as stream flow. “We are pleased that Thermacore k-Core technology helps to support these vital environmental missions,” says Mark Montesano. “Thermal management is essential to the electronics used on these missions, and we’re proud to help meet their demanding requirements.”
Thermacore’s k Technology division is currently providing APG-based solutions for a number of aerospace, satellite and military applications. For more information about Thermacore and its thermal management solutions, please visit www.thermacore.com, or visit Thermacore’s Design Center at www.thermacore.com/design-center.
About Thermacore
Founded in 1970, Thermacore specializes in the custom design, development, and manufacturing of highly engineered thermal management and material solutions for a variety of OEM applications across a diversified set of global markets that includes Military/Aerospace, Computer, Communication, Energy Conversion, Medical, Transportation, Test Equipment, and Automotive. With over 40 years of experience in the design, development, and manufacturing of advanced solid conduction assemblies (k-Core® APG system and thermal straps), passive and active two-phase assemblies and systems (heat pipes, vapor chambers, loop heat pipes), liquid cold plates and active pumped liquid cooling systems, cabinet heat exchangers, and custom materials development, Thermacore brings unparalleled engineering design expertise, manufacturing experience, and thermal and material solution performance, quality, and reliability to these markets.
Thermacore employs more than 180 employees at 5 facilities located in the United States (Lancaster, Pennsylvania; Philadelphia, Pennsylvania; Pittsburgh, Pennsylvania; and Ronkonkoma Long Island, New York) and the United Kingdom (Ashington, Northumberland). Thermacore facilities are certified to AS 9100 Rev C., ISO 9001:2008 and ISO 14001:2004 quality standards. For information about Thermacore, visit www.thermacore.com.
Approved for Public Release, Distribution Unlimited
Contact:
Gregg J. Baldassarre
Vice President, Sales and Marketing
E-mail: g.j.baldassarre@thermacore.com
