Jet Edge Exhibiting Cutting-Edge Waterjet Technology at IMTS Booth #B-6252, September 8-13


See Jet Edge's New 90,000psi Intensifier Pump and Michael Waltrip's Napa 55 Car!

(ST. MICHAEL, Minn. - June 25, 2008) -- Jet Edge, Inc. will demonstrate its latest waterjet cutting technologies at the International Manufacturing Technology Show (IMTS), Sept. 8-13 at McCormick Place in Chicago, Ill.

During IMTS, Jet Edge will showcase its versatile High Rail Gantry precision waterjet cutting system and several new products, including the 90,000psi X-Stream xP90-100 intensifier pump, Contact Height Sensor and Pneumatic Drill. Visitors to Jet Edge Booth B-6252 also will have the opportunity to see Michael Waltrip's Napa 55 Sprint Cup car!

Jet Edge High Rail Gantry

Capable of producing complex parts out of virtually any material, the Jet Edge High Rail Gantry features a stable overhead design that allows full access to the work envelope and raises critical components out of the process environment.
Jet Edge utilizes high-volume, low-pressure air around the ball screws and linear motion guides and bearings, which increases durability by preventing contamination from entering these areas. The High Rail Gantry has a ± 0.005" accuracy of motion over the entire work envelope, ± 0.001" linear positional accuracy over 12" travel per axis and ± 0.001" repeatability (bi-directional). It is available in 2' (0.6m) increments from 4X4' (1.2X1.2m) to 24X14' (7.3x4.3m). Custom sizes are available, and the system can easily be expanded in place as a business grows. All Jet Edge precision gantries isolate the catcher tank from the motion system thereby eliminating any vibration in either component allowing maximum part quality. The system can be, and is, used in locations where it is difficult to get electricity.

Jet Edge at IMTS/2

The High Rail Gantry is powered by Jet Edge's leading line of intensifier pumps, which range from 30 to 280hp and operating pressures up to 75,000psi (5,200 bar) During IMTS, show participants will have the opportunity to see the iP60-50 intensifier pump in action. Featuring the most advanced technology for extended-life hydraulics, a reliable tie-rod design and easy maintenance with no threads on the high pressure cylinders, the 50-horsepower iP60-50 produces up to 60,000 psi (4,100 bar), and provides flow rates of 0 to 1.1 gallons (5 liters) per minute to a variety of cutting, surface-preparation or cleaning tools. The iP60-50 provides easy access for all service and maintenance. It features a non-high-pressure cylinder with a warranty - even on replacement cylinders, an improved performance check valve, and low torque requirements. The Jet Edge iP60-50 intensifier pump leads the industry with ease of operation and low operating cost.

Jet Edge waterjet cutting systems are controlled by the AquaVision Di® motion controller. The AquaVision Di guides users through the process from job set-up to production and has numerous standard features that are optional on many competitive systems. With the AquaVision Di®, single parts, mirroring, scaling, part arrays, rotation and plate alignment are right at users' fingertips. The AquaVision Di® is fully networkable, allowing part programs to be generated offline and easily transferred to the system's hard drive for production. Feed rate and acceleration are automatically varied, based on known features of a specific job. Dynamic tool offset, or "cutter compensation," is employed real-time, and an optional real-time pump control allows remote starting and stopping of the pump, dual pressure set points for hard-to-pierce materials, and unlimited data logging of every process parameter imaginable. The AquaVision Di® includes a full-featured hand-held pendant that allows feed rate override, return-to-path, program zero set points, and XYZ axis control.

X-Stream xP90-100 Intensifier Pump

Visitors to the Jet Edge booth will be among the first to see Jet Edge's new X-Stream xP90-100 intensifier pump. Capable of producing pressures in excess of 90,000psi, the 100hp X-Stream achieves much faster cutting speeds and drastically lowers operating costs compared to traditional 60,000psi pumps, enabling users to increase productivity and reduce part costs. The X-Stream produces 50% more pressure than a 60,000psi intensifier pump, resulting in a 40-50% increase in productivity for many materials. The X-Stream supports a 75,000psi continuous operating pressure. Compared to a 60,000psi pump, typical operating pressures of 75,000psi use 30% less water, 30% less power, and up to 50% less abrasive, resulting in a 40% reduction in operating costs. They typically reduce taper by up to 0.001". The X-Stream is capable of producing flow rates of 1.45gpm and supports up to a .017" orifice. Its fittings and tubing are rated for 100KSI. The X-Stream is backed by nearly 10 years of extensive research and development in hyper-pressure technology.

Jet Edge at IMTS/3

Jet Edge Pneumatic Drill

Jet Edge's new self-feeding pneumatic drill is available in stationary or laterally adjustable models. The drill gives waterjet operators the opportunity to expand their cutting capabilities and take in new types of work by enabling them to quickly pierce sensitive materials prior to cutting them with waterjet. It also can be used for reaming holes to a precise diameter. Its heavy-duty, corrosion-resistant design ensures a maximum operating life.

The drill features a hydraulic feed control unit, feed stroke adjustment, exhaust collector and PLC interface manifold. A flexible bellows cover is mounted to the front of the drill to protect it from foreign material, with all controls contained internally. The drill has a free running rpm of 3,300 and can be set for any stroke from 5/16 to 3 inches. It is supplied with a ¼-inch stainless steel drill chuck. All control valves are contained within a NEMA-rated electrical enclosure.

Jet Edge Contact Height Sensor

With Jet Edge's Contact Height Sensor, waterjet operators can overcome significant fluctuations in material flatness by maintaining a constant automatic standoff within approximately 0.040" (1 mm) of a set standoff height. As a result, they will achieve optimum cut quality, tolerance, taper and speed without having to monitor the standoff.
Jet Edge's Contact Height Sensor senses directly around the nozzle so the information is as close as possible to the nozzle location. The sensor arm can either ride on the plate or have infinite programming for the time it is in contact and raised. This gives operators complete control over how they want the height sensing to work for their application.

Jet Edge's AquaVision Di controller software also provides feature avoidance for the Contact Height Sensor. This protects the height sensor and cutting head by automatically providing a tool path that will not allow the cutting head to pass over a previously-cut part which can tip up after being cut. The software can be configured to allow up to four heads with height sensing to be controlled independently.
Jet Edge's Contact Height Sensor is compatible with the company's Permalign abrasivejet cutting head.

About Jet Edge

Established in 1984, Jet Edge is a global designer and manufacturer of waterjet systems for precision cutting, surface preparation and coating removal. Jet Edge systems are used around the world in a broad range of industries, from the world's leading airlines to automotive, aerospace, industrial manufacturers, machine and job shops. Jet Edge waterjet systems are proudly made in the U.S.A. For more information about Jet Edge, visit www.jetedge.com, e-mail sales@jetedge.com or call 1-800-JET-EDGE (538-3343).

Jet Edge, Inc.

www.jetedge.com

800-JET-EDGE

sales@jetedge.com

CONTACT:

Nancy Lauseng

Marketing Manager

763-497-8726

nancyl@jetedge.com

All Topics