High-Speed Data Converter MFC has eight 250 MHz 16-bit A/Ds.
Press Release Summary:
Multichannel Flexor™ Model 3316 comes with functions for data capture, synchronization, time tagging, and formatting. Standard functions, plus 8 DDCs, enable high performance data capture and transfer modes. While front end accepts 8 analog HF or IF inputs on front panel connectors transformer coupled to 4 TI ADS42LB69 dual ADCs, internal timing bus provides all timing and synchronization required by ADCs. Onboard clock generator and built-in clock synthesizer circuit are also standard.
Original Press Release:
Pentek Extends Flexor Family of Software Radio FMCs
• Eight-channel 250 MHz, 16-bit A/D FMC module
• On-board timing bus generator with multi-board synchronization
• Complete radar or software radio solution when bundled with Model 5973 3U VPX FMC carrier with Virtex-7 FPGA
• Ruggedized versions for harsh military environments
UPPER SADDLE RIVER, NJ—Pentek, Inc., today introduced a new member of its Flexor™ line of FMC (FPGA Mezzanine Card) modules: the Flexor Model 3316 multichannel, high speed data converter FMC. The Model 3316 FMC doubles the existing channel density and boosts sample rates with eight 250 MHz 16-bit A/Ds. The front end accepts eight analog HF or IF inputs on front panel connectors transformer coupled to four Texas Instruments ADS42LB69 dual A/D convertors. The high pin-count FMC connector is ideally matched to the Pentek Model 5973 3U VPX Virtex-7 FPGA carrier for high channel count deployable systems. Pentek also supplies 3316 example code for the Xilinx PCIe FMC 707 Virtex-7 evaluation board as an alternate development scenario.
“Customers driven to get hundreds of channels of analog to digital in a system often ask, ‘What’s my cost per channel,” said Rodger Hosking, vice-president of Pentek. "The Model 3316 doubles the channel density for a single slot, key to bringing down the cost per channel.”
An internal timing bus provides all timing and synchronization required by the A/D converters. An onboard clock generator can receive an external sample clock from the front panel coaxial connector that can be used directly as the sample clock or divided by a built-in clock synthesizer circuit. Alternately, the sample clock can be sourced from an on-board programmable VCXO (Voltage-Controlled Crystal Oscillator) where the front panel coaxial connector can be used to provide a 10 MHz reference clock to phase-lock the internal oscillator.
Bundling for Seamless Integration
“FMCs offer a tremendous amount of design flexibility to embedded platforms,” said Hosking, “but bundling with optimized FPGA code on the carrier is critical for fast integration, best performance and advanced features. Pentek IP core functions on the Model 5973 carrier bring out the best capabilities of the Model 3316 FMC.”
The Flexor Model 5973 comes preconfigured with a suite of built-in functions for data capture, synchronization, time tagging and formatting, all tailored and optimized for specific FMC modules, including the Flexor Model 3316. These standard Model 5973 functions, plus eight digital down converters (DDCs), enable high performance data capture and transfer modes to provide an ideal turn-key signal interface for radar, communications, or general data acquisition applications, eliminating the integration effort typically left for the user when integrating FMC and carrier.
Development Tools and Software Support
With a Pentek carrier, developers have an ideal development and deployment platform for applications requiring custom IP. The Pentek GateFlow® FPGA design kit gives users access to the complete factory installed IP at the source level, allowing them to extend or even replace the built in functions.
The Pentek GateXpress® PCIe configuration manager supports dynamic FPGA reconfiguration though software commands as part of the runtime application. This provides an efficient way to quickly reload the FPGA, which normally occurs many times during development. For deployed environments, GateXpress enables reloading the FPGA without the need to reset the host system, ideal for applications that require dynamic access to different IP algorithms or for live updates.
The Pentek ReadyFlow® Board Support Package is available for Windows and Linux operating systems. ReadyFlow consists of a C-callable library, a complete suite of initialization, control and status functions, as well as a rich set of precompiled, ready-to-run-examples to accelerate application development.
Form Factors, Pricing and Availability
The Flexor Model 3316 FMC is designed for air-cooled, conduction-cooled, and rugged operating environments. The Model 3316 price starts at $3,495 USD when purchased with the Model 5973 FMC carrier. Delivery is 8-10 weeks ARO.
About Pentek
Pentek develops, manufactures and markets advanced DSP systems and recorders to original equipment manufacturers, distributors and value-added resellers. Pentek offers powerful VME, VPX, PMC, XMC, FMC, cPCI, PCI, PCIe and AMC boards for data acquisition, software radio and digital signal processing featuring Xilinx FPGAs, Texas Instruments C6000 DSPs, and Freescale G4 PowerPCs. Pentek's I/O includes A/Ds, D/As, FPGAs, Serial FPDP, LVDS, RF converters and more. Pentek equips all products with high-performance I/O including gigabit serial interfaces and offers strong DSP software support.
Pentek, Onyx, GateXpress, ReadyFlow, GateFlow and Flexor are trademarks or registered trademarks of Pentek, Inc. Brand or product names are registered trademarks or trademarks of their respective holders.
For access to the release and data sheets, please visit: http://www.pentek.com/whatsnew/viewrelease.cfm?index=197
North American Sales Contact: Mario Schiavone, Pentek, Inc., One Park Way, Upper Saddle River, NJ 07458-2311; Telephone 201-818-5900; Fax 201-818-5904; Email news@pentek.com; Website www.pentek.com.
