CULTEC Stormwater Chambers Solve On-Site Challenges for "Green" Orange County Choppers Facility


Engineers Switch to Underground Stormwater System to Minimize Disturbance and
Fulfill Zero Discharge Requirements

BROOKFIELD, CT/June 11, 2008 - When civil engineers from Day Engineering began designing a stormwater system for the new Orange County Choppers' headquarters and showroom facility in Newburgh, N.Y., they met with a variety of on-site challenges. These included a lack of available land, a high water table with a neighboring protected stream and a zero discharge restriction. In addition, the engineers wanted to ensure that the stormwater system would create minimum land disturbance in the eco-friendly development. They specified a lot of recycled and locally processed building materials, with no formaldehyde or urea, and used energy-efficient equipment and recycled their construction waste. The engineers also planned to use the stormwater captured on the site for irrigation.

Stone-filled trenches and above-ground detention ponds that the engineering firm had relied on previously could not fulfill the site's requirements. Instead, for the first time the town of Newburgh used CULTEC underground plastic chambers as the site's Best Management Practice for controlling stormwater.

"When an open detention pond is used to control stormwater run-off, the site loses acreage," said Larry Ruscitti, Site Supervisor at Ultimate Land Developers, Inc. "At (the) Orange County Choppers' development, they needed to use a smaller footprint because there was a water stream at the back of the property. The CULTEC system allowed for some extra space they wouldn't have had with an above-ground system. That space was later used to add to a parking lot and create a grassy area."

The Recharger V8 - currently CULTEC's largest-capacity stormwater storage chamber -- was selected. The stormwater system collects water in catch basins and feeds it into the underground chambers where it is treated and retained until it can be infiltrated back into the ground. That satisfies the zero discharge requirement that all stormwater run-off be captured, treated and stored on-site to preserve water quality of the local waterways.

The 400-chamber system occupies 17,000 sq. feet of the 3.2-acre development area, offering approximately 50,000 cubic feet of storage capacity. The installation began with excavating a bed, laying filter fabric along the sides and the bottom and adding a layer of crushed stone. After the V8 chambers were in place they were backfilled with stone, covered with a layer of filter fabric, and prepared for asphalt. The filter fabric encapsulated all the stone to ensure protection from soil intrusion. The entire system was installed in a week and a half, with the excavation process taking most of that time.

"The CULTEC system was installed very quickly, with only half a day needed to install the chambers," said Dennis Lynch, Field Engineer at Day Engineering. "It was the first time we ever used an underground system, and CULTEC walked us through every step of its design, layout and configuration."

CULTEC Recharger V8 stormwater chambers have more than 40% greater storage capacity than CULTEC's next largest model and can be used for retention, detention, recharging, or controlling the flow of on-site stormwater run-off. The chamber incorporates all of the distinctive key benefits of CULTEC chambers, including built-in endwalls for strength throughout the system and a patented, overlapping rib connection, which allows for easy installation and a stronger connection between chambers. The Recharger V8 stormwater system uses a unique in-line manifold system which allows for additional design flexibility. CULTEC chambers are constructed of high-density polyethylene for greater chemical resistance to parking lot run-off.

For more information, please call (800) 4-CULTEC or visit www.cultec.com.

CULTEC, Inc., headquartered in Brookfield, Connecticut, is a national manufacturer of plastic chambers used in subsurface retention/detention stormwater management systems and septic applications. In addition, CULTEC has designed its own manifold and water quality systems to complement its product line. CULTEC currently offers the largest variety of sizes and types of products of any chamber manufacturer. The company's Recharger® and Contactor® chambers are used extensively in Clean Water Act applications, and utilize high-density polyethylene material, a patented interlocking rib connection and fully-formed endwall to achieve long life and durability.

PRESS CONTACTS:

Melissa LoParco

Yuliya Kutuzava

Catalyst Marketing Communications, Inc.

(203) 348-7541

All Topics